COLOR MONITOR SERVICE MANUAL CHASSIS NO. : CL-32 FACTORY MODEL: LB501K MODEL: L1511S (LB501K-GL) CAUTION BEFORE SERVICING THE UNIT, READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
PRECAUTION WARNING FOR THE SAFETY-RELATED COMPONENT. WARNING • There are some special components used in LCD BE CAREFUL ELECTRIC SHOCK ! monitor that are important for safety. These parts are • If you want to replace with the new backlight (CCFL) or marked on the schematic diagram and the inverter circuit, must disconnect the AC adapter...
TIMING CHART VIDEO SYNC Total Video Blanking Sync Back Front Sync Frequency MODE H / V Resolution Period Active Time Duration Porch Porch Polarity Clock ( E ) Time ( A ) ( B ) ( D ) ( F ) ( C ) 25.175 31.468 KHz...
OPERATING INSTRUCTIONS FRONT VIEW REAR VIEW Power Connector D-Sub Signal Connector See front control panel Front Control Panel 1. Power Button 4. AUTO/SELECT Button Use this button to turn the display on or off. Use this button to enter a selection in the On <Power (DPMS) Indicator>...
DESCRIPTION OF BLOCK DIAGRAM 1. Scaler One chip IC(GMZAN-2, U201) GMZAN-2 (U201) is one chip IC which it supports four internal function blocks of Video Amp, PLL, A/D converter and Video processor. Video signal (0.7Vp.p) clamped through C207, 208, 209 with matching IC’s proper cut off voltage. This signal is processed as a proper 8 bit digital signal by U201’s amplifying, phase locking, A/D converting, and scaling operations.
ADJUSTMENT All adjustment are thoroughly checked and corrected 2. Adjustment for White Balance when the monitor leaves the factory, but sometimes 1) Display color 0,0 pattern at Mode 13. several minor adjustment may be required. 2) Set External Bright to MAX position and Contrast to Adjustment should be following procedure and after MAX Position.
TROUBLESHOOTING GUIDE 1. NO POWER NO POWER (POWER INDICATOR OFF) CHECK POWER BOARD, AND FIND CHECK J705 OUT A SHORT POINT VOLTAGE PIN5, PIN6 (5V)? AS OPENING EACH POWER LINE CHECK U802 PIN 1 CHECK U803. VOLTAGE (5V) ? CHECK CHECK 5VS LINE U805 PIN 1 Voltage (OPEN CHECK)
Page 11
2. NO RASTER (OSD IS NOT DISPLAYED) – LIPS NO RASTER (OSD IS NOT DISPLAYED) J705 PIN5, PIN 6 CHECK LIPS CHECK MICOM INV J705 PIN2 ON/OFF PORT. 1. CONFIRM BRIGHTNESS OSD CONTRL STATE. J705 PIN1 2. CHECK MICOM DIM-ADJ PORT CHECK PULSE AS...
Page 12
3. NO RASTER (OSD IS NOT DISPLAYED) – gmZAN2 NO RASTER (OSD IS NOT DISPLAYED) U201 POWER PINS CHECK U802, U806 3.3V? 1. CHECK PIN141, 142 U201 PIN141, 142 SOLDERING CONDITION OSCILLATE AS 20MHZ? 2. CHECK X201 3. TROUBLE IN U201 U401 PIN31 IS 65MHz CLOCK? PIN27 IS 48KHz H-SYNC?
Page 13
4. NO RASTER (OSD IS DISPLAYED) – gmZAN2 NO RASTER (OSD IS DISPLAYED) U201 POWER PIN CHECK U802, U806 3.3V? 1. CHECK PC CHECK 2. CHECK SIGNAL CABLE R,G,B INPUT? & D-SUB CONNECTOR U201 PIN 87, 91, 95 LINE CHECK CHECK H-SYNC LINE H-SYNC INPUT (D-SUB U701 MICOM...
REPLACEMENT PARTS LIST CAUTION: BEFORE REPLACING ANY OF THESE COMPONENTS, READ CAREFULLY THE SAFETY PRECAUTIONS IN THIS MANUAL. * NOTE SAFETY Mark AL ALTERNATIVE PARTS DATE: 2002. 8. 29. DATE: 2002. 8. 29. *S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION *S *AL LOC.
PIN CONFIGURATION CAT24WC02J-TE13 8P BLOCK DIAGRAM DIP Package(p) SOIX Package(J) EXTERNAL LOAD V CC V CC SENSE AMPS D OUT SHIFT REGISTERS V SS V SS V CC COLUMN V SS WORD ADDRESS DECODERS BUFFERS TSSOP Package(U) START/STOP LOGIC V CC E PROM XDEC V SS...
Page 21
THC63LVDM83R PIN CONFIGURATION BLOCK DIAGRAM THC63LVDM83R THC63LVDM83R DATA (LVDS) TA +/- TA0-6 LVDS GND TB0-6 TB +/- TC0-6 TC +/- LVDS VCC TD0-6 LVDS GND TD +/- (140-595Mbit/On Each TCLK - LVDS Channel) TRANSMITTER TCLK+ TCLK +/- CLOCK IN (20 to 85MHz) CLOCK LVDS GND (LVDS)