Advertisement
thank you for purchasing a sealey product. manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
Wear eye
instructions
protection
1. saFetY
i
1.1.
electRical saFetY
ONLY USE THE SUPPLIED TRANSFORMER PLUG FOR CONNECTING UNIT TO THE MAIN ELECTRICAL POWER SUPPLY.
WaRning! It is the user's responsibility to read, understand and comply with the following electrical instructions:
‰
You must ensure the risk of electric shock is minimised by the installation of appropriate safety devices. An RCCB (Residual Current
Circuit Breaker) should be incorporated in the main distribution board. We also recommend that an RCd (Residual Current device) is
used with all electrical products, particularly portable equipment which is plugged into an electrical supply not protected by an RCCB.
You must also read and understand the following instructions concerning electrical safety.
1.1.1.
The Electricity At Work Act 1989 requires all portable electrical appliances, if used on business premises, to be tested by a qualified
electrician, using a Portable Appliance Tester (PAT), at least once a year.
1.1.2.
The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of the appliance and
the safety of the appliance operator. If in any doubt about electrical safety, contact a qualified electrician.
1.1.3.
You must ensuRe that You:
Inspect the transformer plug, cable and connector for wear and damage to ensure items are safe before connecting to the mains power
9
supply. If worn or damaged do not use but immediately replace, or contact a qualified electrician.
Check cables are always protected against short circuit and overload.
9
Important: Check that the voltage marked on the transformer plug is the same as the power supply to be used.
9
Uncoil the cable between the transformer and the cabinet.
9
do not pull transformer lead, or pull the transformer plug from the mains socket by the lead.
8
do not use any other type of transformer with this product.
8
do not place the power connector into any area of the cabinet other than the correct inlet socket.
8
do not try to open or dis-assemble the transformer plug.
8
do not use the transformer plug to power any other electrical item.
8
do not get the transformer wet, or use in wet, damp conditions (for indoor use only).
8
WaRning! neVeR substitute a standard 13 Amp 3 pin plug, or any other type of plug, for the transformer plug.
‰
cable extension Reels. When a cable extension reel is used it should be fully unwound before connection. A cable reel with an
RCd fitted is recommended since any product which is plugged into the cable reel will be protected. The section of the cable on the cable
reel is important and should be at least 1.5mm², but to be absolutely sure that the capacity of the cable reel is suitable for this product and
for others that may be used in the other output sockets, we recommend the use of 2.5mm² section cable.
1.2.
geneRal saFetY
WaRning! ensure Health & Safety, government and local authority regulations relating to the the use of shot blasting are adhered to
‰
when using this equipment. Familiarise yourself with the applications, limitations and potential hazards peculiar to the cabinet.
WaRning! disconnect cabinet from mains power and air supply before changing accessories, servicing or performing any maintenance.
‰
maintain the cabinet in good condition. Replace or repair damaged parts. Use genuine parts
9
only. Unauthorised parts may be dangerous and will invalidate the warranty.
locate cabinet in a suitable work area, keep area clean, tidy and free from unrelated
9
materials. ensure adequate lighting.
▲
imPoRtant. Use only dry abrasives such as glass bead. We recommend Sealey item
B5KG. never use fluids or mix fluids with another media in unit.
WaRning! Always wear approved eye or face and ear protection when operating the
‰
cabinet.
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and
9
contain and/or tie back long hair.
Keep the side doors closed and secured when in use.
9
WaRning! ensure correct air pressure is maintained and not exceeded. Always
‰
keep blast nozzle directed at the workpiece. do not aim blast at gloves, glove
fingers or internal light. never use outside the unit. Regularly check that the exhaust vent at
the back of the cabinet is clear and that there is space between it and any wall.
maintain correct balance and footing. ensure the floor is clean and free from blasting grit
9
spillage. Wear non-slip shoes.
Keep children and non-essential persons away from the work area.
9
do not use the cabinet to achieve a task it is not designed to perform.
8
© Jack Sealey limited
shot blasting cabinet double access
960 x 720 x 1500mm
model no:
Wear protective
Wear safety
gloves
footwear
Original Language Version
sb974.V5
Wear protective
Wear ear
clothing
protection
Wear a mask
Transformer Plug
SB974.V5
Issue 3
19/08/19
Advertisement
Table of Contents
Related Manuals for Sealey SB974.V5
Summary of Contents for Sealey SB974.V5
- Page 1 IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
- Page 2 If not using an extraction system, remove the cover from air flow outlet (Z) at rear right hand side of the cabinet to allow air flow. SB974.V5 Issue 3 (3,4) 21/08/19 Original Language Version © Jack Sealey limited...
- Page 3 1. dry weather conditions. 1. leave the workpiece to stand for a while. Blast pattern too wide or ineffective. 1. nozzle blocked or worn. 1. Unblock or replace nozzle Original Language Version SB974.V5 Issue 3 (3,4) 21/08/19 © Jack Sealey limited...
- Page 4 Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim. sealey group, Kempson Way, suffolk business Park, bury st edmunds, suffolk. iP32 7aR 01284 757500 01284 703534 sales@sealey.co.uk...