Advertisement
Quick Links
FLOOR Models:
BENCH Models:
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.
USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE
OR PERSONAL INJURY, AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
1.2
GENERAL SAFETY
! Familiarise yourself with this products application and limitations, as well as the specific potential hazards peculiar to the press.
! Maintain the press in good condition (use an authorised service agent).
! Replace or repair damaged parts. Use recommended parts only. Non authorised parts may be dangerous and will invalidate the warranty.
! Keep the press clean for best and safest performance.
! Locate the press in an adequate working area for its function, keep area clean and tidy and free from unrelated materials, and ensure
there is adequate lighting.
! Ensure the workpiece is correctly secured before operating the press.
F WARNING! Always wear approved eye or face protection when operating the press.
! Remove ill fitting clothing. Remove ties, watches, rings, and other loose jewellery, and contain long hair.
! Keep hands and body clear of the work table when operating the press.
! Maintain correct balance and footing. Ensure the floor is not slippery and wear non slip shoes.
! Keep children and unauthorised persons away from the working area.
% DO NOT operate the press if any parts are missing as this may cause failure or possible personal injury.
% DO NOT force the press to achieve a task it was not designed to perform.
% DO NOT adjust or tamper with the safety valve.
% DO NOT exceed the rated capacity of the press.
% DO NOT apply off centre loads.
% DO NOT allow the workpiece of the arbor plates to fall from the press working bench.
% DO NOT get the press wet or use in damp or wet locations or areas where there is condensation.
% DO NOT operate the press when you are tired, under the influence of alcohol, drugs or intoxicating medication.
! When not in use release pressure from the pump and clean the press. Stand or store the arbors in a safe location.
2. INTRODUCTION & SPECIFICATIONS
2.1.
GENERAL INFORMATION
The Sealey range of heavy duty floor and bench hydraulic presses are ideal for a variety of workshop applications and are particularly suited
to agricultural or industrial use. Jobs such as straightening, bending, folding, punching, removing bolts and bearings etc are some of tasks that
may be accomplished by your press. All models are fitted with pressure gauge and work-table V-blocks except where stated. The “BM” and “FM”
range of press units feature integrally mounted rams giving more vertical clearance between the table and ram head enabling larger items
to be fitted on the working table.
F
WARNING! All models are purpose designed to withstand greater loads than the hydraulic units can develop. For safety reasons, always
F
ensure the workpiece is secured on table and loads that flex will not suddenly “give” causing danger to operator or damage to component.
p
p
2.2. SPECIFICATIONS
Model:
YK15BLG
Capacity
Ram Stroke
150mm
Extension screw
60mm
Ram to table
300mm
Min Ht-Ram to table
150mm
Table Aperture
112mm
Work table width
500mm
Overall Height
945mm
Gauge Included
Weight
69kg
3. ASSEMBLY
Unpack product and check contents against
Take care to ensure safety when removing main frame from packing as the unit is very heavy. Retain pressure gauge in carton until required,
and do not remove white tape from gauge mount or masking tape from the angle arm.
Contents:
!Frame !legs x2 !worktable x1 !worktable pins x2 !v-blocks x2 !pump handle x1 !pressure gauge x1 (except model YK15BLG)
!gauge angle arm connector x1. 50Ton models incorporate winch handle.
3.1.
Press Assembly
3.1.1. Identity and lay out parts. Handle the main frame with care and lay horizontally allowing the cross legs to be bolted on to the bottom
of the pre-assembled main frame. Note: care must be taken when handling the main frame to ensure stability. DO NOT allow to fall.
YK15, YK15FM, YK30, YK30FM, YK50FM.
YK10BM, YK15BLG, YK15BM.
YK10BM
YK15BM
15T
10T
95mm
70mm
455mm
155mm
140mm
500mm
1035mm
no
yes
65kg
list
below. Should there be any damaged or missing parts contact your supplier immediately.
INSTRUCTIONS FOR:
HYDRAULIC BENCH & FLOOR PRESS
YK15
15T
15T
95mm
150mm
70mm
60mm
455mm
600mm
155mm
150mm
140mm
112mm
500mm
500mm
945mm
1675mm
yes
yes
69kg
80kg
YK15FM
YK30
15T
30T
95mm
150mm
67mm
60mm
600mm
600mm
150mm
150mm
140mm
133mm
500mm
550mm
1650mm
1750mm
yes
yes
86kg
122kg
YK10BM, YK15, YK15BLG, YK15BM, YK15FM, YK30, YK30FM, YK50FM. - 0025 - 050897
YK30FM
YK50FM
30T
50T
95mm
95mm
70mm
70mm
620mm
615mm
180mm
165mm
143mm
170mm
550mm
550mm
1750mm
1830mm
yes
yes
125kg
240kg
Advertisement
Related Manuals for Sealey YK15
Summary of Contents for Sealey YK15
- Page 1 GENERAL INFORMATION The Sealey range of heavy duty floor and bench hydraulic presses are ideal for a variety of workshop applications and are particularly suited to agricultural or industrial use. Jobs such as straightening, bending, folding, punching, removing bolts and bearings etc are some of tasks that may be accomplished by your press.
- Page 2 Should you need to replace oil ensure piston is fully retracted. An excess of oil will render press inoperative. Use only appropriate Sealey hydraulic oil. DO NOT use brake fluid. Contact your local Sealey dealer for details. Purge the system to remove any air.