Cisco WAP121 Quick Start Manual
Wireless-n access points
Hide thumbs
Also See for WAP121:
- Administration manual (179 pages) ,
- Quick start manual (13 pages) ,
- Datasheet (7 pages)
Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Cisco WAP121
Summary of Contents for Cisco WAP121
-
Page 1: Quick Start Guide
Quick Start Guide Cisco WAP121 and WAP321 Wireless-N Access Points... -
Page 2: Before You Begin
Thank you for choosing the Cisco WAP121 or WAP321 Wireless Access Points.The Cisco WAP321 is a single radio, selectable-band, 2.4 GHz or 5.0 GHz 802.11n access point, and the Cisco WAP121 is a single-band 2.4 GHz variant of the Cisco WAP321. -
Page 3: Access Point Features
Subnetwork Mask 255.255.255.0 If you are using a Cisco RV Series router, the default range for the DHCP assigned address is from 192.168.1.100 to 192.168.1.254. Any device connecting to the same LAN will be assigned an IP address in this range. -
Page 4: Placement Tips
Wall and Ceiling Mounting The Cisco WAP121 and WAP321 can be wall or ceiling-mounted. There is a mounting kit packed with your device. The kit is designed to install your device to the wall or the ceiling. The dimensions for the mount kit screws are as follows: 1 7.8 to 8.3 mm/... - Page 5 Connect the other end of the network Ethernet cable to the Ethernet port of the wireless access point. If PoE is not provided, for the Cisco WAP121 plug in the power adaptor to provide power to the device. For the Cisco WAP321, the power adaptor is sold separately.
-
Page 6: Verifying The Hardware Installation
• GE link is detected for Cisco WAP321 Solid Amber Ethernet link is active. • FE link is detected for Cisco WAP321 Flashing Transmitting/Receiving Data If you need help resolving a problem, visit the Cisco Support Community at www.cisco.com/go/smallbizsupport. Cisco WAP121 and WAP321 Wireless-N Access Points... -
Page 7: Getting Started With The Configuration
In the Address field enter the default DHCP address and press the Enter key. Enter the default user name of cisco and password of cisco in the User Name and Password fields. Click Login. The Wireless Access Point Setup Wizard appears. -
Page 8: Troubleshooting
To use ping on a computer running Windows: Verify that the Cisco WAP121 or WAP321 is powered on and the lights indicate the appropriate links. Locate the device’s IP address. While there are different ways to locate your device’s IP address, this procedure uses Cisco FindIT. - Page 9 The most likely cause of connectivity failure is an incorrect IP address. The Web browser may be pointed to the wrong IP address, or your computer may be configured with an IP address that is not in the same subnet as the device. Cisco WAP121 and WAP321 Wireless-N Access Points...
-
Page 10: Rebooting The Devices Or Returning Them To Their Factory Default Settings
• To restore the device to the factory default settings, with the power on, press-and-hold the Reset button with a bent paperclip for more than 10 seconds. – All of the lights will go off. – Release the Reset button when power light turns on. Cisco WAP121 and WAP321 Wireless-N Access Points... -
Page 11: Where To Go From Here
For EU lot 26 related test result, please check this web page: www.cisco.com/go/eu-lot26- results Cisco Firmware www.cisco.com/go/smallbizfirmware Downloads Select a link to download firmware for Cisco Products. No login is required. Cisco Open Source www.cisco.com/go/ Requests smallbiz_opensource_request Cisco Partner Central www.cisco.com/web/partners/sell/smb... - Page 12 Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners.