E-mail: http://www.LGEservice.com/techsup.html COLOR MONITOR SERVICE MANUAL W2243T MODEL: ( W2243T-PFT.A**NAPH for LGD TLA1, W2243T-PFT.A**VAPH for AUO V0 ) **Sales Market CAUTION BEFORE SERVICING THE UNIT, READ THE SAFETY PRECAUTIONS IN THIS MANUAL. *To apply the Novatek Chip. - 1 -...
DISASSEMBLY-Set Put the monitor on a soft flat. Revolve the release button. Consequently, pull the base directly. The base. Put the front cover upward. Then let the all Put the front face down, disassembly back latches are separated. cover.
Page 10
#8 Pull the key board out of bezel. Disassembly the bezel. Disassembly the LVDS cable. Disassemble the connector. Main board and power board. The panel. - 10 -...
Page 11
Rear cover and hinge ASS’Y. Disassemble the rear cover and hinge ASS’Y. Disassemble the hinge and stand. Hinge top, hinge and stand. - 11 -...
DESCRIPTION OF BLOCK DIAGRAM 1. Video Controller Part. This part amplifies the level of video signal for the digital conversion and converts from the analog video signal to the digital video signal using a pixel clock. The pixel clock for each mode is generated by the PLL. The range of the pixel clock is from 25MHz to 148.5MHz.
LIPS Board Block Diagram Operation Description_LIPS 1. EMI components. This part contains of EMI components to comply with global marketing EMI standards like FCC, VCCI CISPR, the circuit included a line-filter, across line capacitor and of course the primary protection fuse. 2.
ADJUSTMENT Windows EDID V1.0 User Manual Operating System: DOS, windows98, 2000, XP 1. Parallel port setting Enter your bios, and do as followings. a) Integrated peripheral b) Super IO Device c) Parallel port mode you should set the” parallel port mode” to SPP for using the DOS EDID tool surely. 2.
Page 17
Please check Manufacturer Name、 Vendor Assigned Code、 Monitor Name、 Serial Number: *****[???????? ******] (it must be the same as Bar Code)、 Week of Manufacture:**、Year of Manufacture:****、Check sum:** (It must be the same as the last byte of data table, as follows picture shows). Above of all must be right, then if it shows the green “PASS”, it means record succeeds ,the red “Fail”...
SERVICE MODE 1) Turn off the power switch at the front side of the display. 2) Wait for about 5 seconds and press MENU, POWER switch with 1 second interval. 3) The SVC OSD menu contains additional menus that the User OSD menu as described below. a) CLEAR ETI: To initialize using time.
TROUBLESHOOTING GUIDE 1. NO POWER No Power (Power Indicator Off) Check the Adapter/Inverter Please reinsert and section make sure the AC of 100-240v is normal Measure U704 Check CN701 or replace PIN2=1.8V U704, and U703 U703 PIN2=3.3V Check X401 oscillate Replace X401 waveforms are normal ...
Page 20
2. NO RASTER (OSD IS NOT DISPLAY)-LIPS No Raster (OSD Is Not Displayed) Check power board and find out a Check CN701 short point as penning each power PIN 6, PIN7 =5V? line Check U703 Check U703 Check C706,C707 PIN 2 =3.3V? 1.
Page 21
3. NO RASTER (OSD IS NOT DISPLAY)-MSTAR No Raster (OSD Is Not Displayed) SCALER PIN 127, 1. Check C420 C421 128 OSCILLATES 2. Check X401 AS 12MHZ? 3. TROUBLE IN SCALER IC CHECK CONNECTION SCALER IC LINE FROM D-SUB TO PIN 41 H SYNC ? SCALER PIN 42 V SYNC?
Page 22
4. TROUBLE IN DPM TROUBLE IN DPM SCALER IC PIN 41 H SYNC? CHECK H/V SYNC LINE PIN 42 V SYNC? TROUBLE IN CABLE OR LCD MODULE - 22 -...
Page 23
5. POWER No Power (Power Indicator Off) Check AC line Check AC line volt Check F901, BD901 Check the voltage of C907(+) Check start Check D901, R903, voltage for the pin1 R904,R905,U901 of U901 Check U901 pin 6 Check D902,C911 Vcc is 13v? Check U901 PIN5 Check D904,Q901 ...
Page 24
6. RASTER NO Raster (Lamp Off) Check C804 (+) Check power section =16V Check Interface section or Check ON/OFF main board signal CheckIC801 pin Check C808, C809, C810 11=5V? Check IC801 Check IC801 pin 1/pin 14 Pin8/pin9 have the output of sawtooth Replace IC801...
DIFFERENT PARTS LIST W2243T Diversity of TI9GNDM8MWLGNN Compared with TIRANDNBMWLFHN Location Part No. for TPV Description 750GLG215W1A13M0LG PANEL LM215WF1-TLA1 GZ LGD 756GQ9CB KL002 MAIN BOARD-CBPCRNDLGQ2 SMTCR-U402 100GKNGI000NT1 MCU ASS'Y- 056G1133 81 Q34G0576 B6B2B0100 BEZEL L215W-9LG - 37 -...