Related Manuals for Honeywell VSD-261P
Summary of Contents for Honeywell VSD-261P
- Page 1 VISTA Series VSD TM Speed Dome VSD-261P Operation Manual Read this Manual carefully before installation and keep it by hand for future reference.
- Page 2 CAUTION Persons without technical qualifications should not attempt to operate this dome device before reading this Manual thoroughly. Remove any power to the dome before attempting any operations or adjustments inside the dome cover to avoid potential damage to the mechanism. Inside the dome cover there are precision optical and electrical devices.
-
Page 3: Table Of Contents
Table of Contents ……………………………………………1 Auto AF…………………………………………18 Cautions Auto AE…………………………………………18 …………………………………1 Package contents ………………………1 ………………………………18 Chapter One – Introduction Vector Scan AF Vector Scan Still …………………………………18 ………………1 Performance Characteristics ………………………1 4.5 Diagnostic Options ……………………………18 Features and Functions ………………2 Clear Memory …………………………………18 Chapter Two –... -
Page 4: Package Contents
Package Contents Please check the quantity of the package contents when open the carton. Description Manual, Certificate each1 BNC Wire Rubber Cushion Lower housing of dome Bag of screws High Speed Dome Camera Module Wall bracket AC24V transformer Camera Shroud Terminal Please contact the distributors in time if the spare parts are missing. -
Page 5: Cautions
Chapter One – Introduction 1.1 Performance Characteristics 0～255 individually addressed units. The dome address is defined using a dip switch with 8 positions (Binary addressing scheme). Integrated multi-protocol and auto protocol differentiation. Note: The dome can auto differentiate the protocol of the Controller only on power Up. -
Page 6: Chapter Two - Camera Installation
Intelligent power off real time memory (Should power fail while the dome was in operation，the dome well resume its preprogrammed function upon power restore). Highly efficient 3-dimensional scan function (User can change the pan scan tour when the dome is in manual scan or auto scan between two pan points). -
Page 7: Package Contents
2.2 Package Contents 2.2.1 Below figures illustrate the package contents. Figure 1. Illustrates the Upper layer of the carton (top half), Figure 2. Illustrates the lower layer of the carton (bottom half). Fig 1 Fig 2 Sequence No. Description Manual, Certificate BNC Wire Rubber Cushion Lower housing for the dome, Terminal... -
Page 8: Camera Installation
Sony camera model screw holes Honeywell camera model screw holes Install the camera module on the vertical axis tray of the dome as illustrated in Fig.7 using the Fig.6... -
Page 9: Camera Shroud Installation
2.4 Camera Shroud installation Fig.8 illustrates the location of the 4 screw holes for the camera shroud (M3). Fig.8 Fig.9 Screw holes Tighten the screws Fig.10 Fig.11 2.4.1 Position the open end of the camera shroud towards the camera lens as illustrated on Fig. 9. Align the 4 holes of the shroud with the 4 holes on the core of the dome as illustrated in Fig. - Page 10 Fig. 14 illustrates installation of wall bracket Fig 15 illustrates installation of pendent bracket 4-M8 ? 120.0 70.7 ? 100.0 70.7 25.0 Pendent bracket 4-M6 200.0 260.0 Wall bracket 2-PM4*10 3-PM5*12 3-M5*8 Bracket adapter Bracket adapter 2-PM5*14 252.1 252.1 OD housing 226.7 OD housing 226.7...
-
Page 11: Installation Of The Acrylic Dome Cover
Installation of the acrylic dome cover The way of installation is to rotate the acrylic dome cover. Caution should be exercised when handling the clear dome by wearing cotton glove so as to prevent any abrasions or scratches to the surface as this will affect the optical performance of the camera Installation instruction Carefully align the two parts and slowly rotate counterclockwise as illustrated in Fig. -
Page 12: Wiring Specifications
Wiring Specifications Fig. 19 is the illustration of the wiring diagram for the electrical connections to the dome unit. Fig. 20 illustrates the supplied power Supply. ： Yellow/green Ground wire BNC Connector：Video output Connect to keyboard Orange：RS485+ controller Yellow：RS485- Red, black ： AC24V power Supply Terminal：Connect to the dome device ：... -
Page 13: Chapter Three Basic Configuration
Chapter Three – Basic Configuration Wiring User can understand the dome electric connection property and adjust, assemble, test and operate the device on show with convenience Please read the wiring illustration carefully for the first time use Any wrong connection may cause the permanent damage of the dome or other equipments ：... -
Page 14: Protocol And Baud Rate Setting
： Yellow/green Ground wire BNC Connector：Video output Connect to keyboard Orange：RS485+ controller Yellow：RS485- Red, black：AC24V power Supply Terminal：Connect to the dome device ： Yellow/green Ground wire Caution: This operation should be performed with the power OFF. Before installation and use the unique address for each dome and the communication protocol including transmission speed (baud rate) should be set to correspond with the chosen control system Protocol and baud rate setting（... -
Page 15: Address Setting Of Each Dome
On/Off Baud rate 2400 4800 Thi s fi gur e shows pr otocol of 9600 PELCO- D, Baud r ate of 2400. 19200 Address setting of each dome (Caution: This operation should be performed with the power OFF). Setting method: The sum of switch numbers when it is at ON position is the address of dome device Calculation example of dome device address: (2+4+16=22), the address is 22 Dome device range: 0～255 2 3 4 5 6 7... -
Page 16: Chapter Four Menu Setting
Chapter Four–Menu setting Operation instruction Menu operation To make a selection, move the joystick in the UP or DOWN direction The on-screen arrow points to the selected option Press OPEN or use the joystick to the Left or Right position you can change the value of your selection or enter the submenu for the selected option Press CLOSE to exit menu or return to the previous menu Number... -
Page 17: Display Options
Control Options Diagnostic Options Set the dome in manual or auto operation Data information management setup and make its tilt and pan action as well as Diagnostic Options the camera to be compatible with the whole →1.Clear Memory controlling system and user individual setting 2. - Page 18 PreShot Setup Setup the PreShot position on the menu 1. Move the joystick Left/Right or press OPEN to enter Display Options. PreShot Name 2. Move the joystick Left/Right to move the cursor to select the 1. Number PreShot Options. →2. PreShot Setup 3.
-
Page 19: Setting Of Sector
PreShot Name PreShot Name Edit PreShot Name 1. Number 1. Ref<number input instruction>edit PreShot name.. 2. PreShot Setup 2. Move the cursor to select PreShot name. 3. Call PreShot 3. Move the joystick Left or Right or press OPEN to enter Name 4. - Page 20 Sector Name 1. Select Sector Name. Press OPEN to enter Name Editing. Sector Setup 2. Edit name. 1. Number →2. Name 3. Pan Start POS 4. Pan End POS 5. Tilt Start POS IRIS CLOSE to Exit Pan Start POS 1.
-
Page 21: Coordinates
Steps: Sector Setup Select Name Display and move the joystick Left 6. Tilt End POS →7. Name Display or Right or press OPEN to switch On/Off. IRIS CLOSE to Exit Coordinates Crosshairs Display Options Display Options 1. PreShot Position 1. PreShot Position 2. -
Page 22: Set Default Function
Set Default Function Steps: Set Default Function Move the joystick Up or Down to move the cursor to select Restore Def. →1. Set Default Function Move the joystick Left or Right to setup PreShot Position/ PTZ tour/ 2. Number Vector scan 3. -
Page 23: Color System
Color System Function: Setup video mode of dome same with that of camera. Diagnostic Options Steps: 1. Clear Memory Move the joystick Up/Down to move the cursor to select Video Mode. 2. Restore Def. Setting Note: This camera only supports PAL. →3. -
Page 24: Camera Name
Camera Name 1. Name of camera Camera Name →1. Name Steps: 2. Change Name Loc 1）Move the joystick Up or Down to move the cursor to select Name. 3. Name Display 2）Edit Name (Refer to Chinese Editing Instruction). IRIS CLOSE to Exit 3）Move the joystick Left or Right to setup the Name Display. - Page 25 AE Control 2. Slow Shutter (Manual/ Slow Shutter) 1. AE Mode Auto Steps: →2. Slow Shutter Auto 1) Move the joystick Up or Down to move the cursor to select Slow 3. Shutter Speed Auto Shutter. 4. Iris Level Auto 2) Move the joystick Left or Right to setup.
-
Page 26: Camera Exposure
Setup Mask Zone Camera Options 1. Camera Name Function: User can mask the zone and protect the mask area. 2. Zoom and Focus 3. Camera Exposure 1. Number →4. Mask Zone 5. Mask Color Steps: 6. Others 1) Move the joystick to move the cursor to select Number. IRIS CLOSE to Exit 2) Move the joystick Left or Right to select desired editing mask zone (1-24). -
Page 27: Others
2. Mask Color Mask Color Steps: 1. Mask Color Red 1) Move the joystick Up or Down to move the cursor to select →2.Semi-transparency On/Off Semi-transparency. IRIS CLOSE to Exit 2) Move the joystick Left or Right to start or close Semi-transparency. Others Others →1.Sharpness... -
Page 28: Program Vector Scan
6. Move the joystick Up or Down to move the cursor to select PTZ Tour. PTZ Tour 7. Press OPEN to enter Manual Operation Tour Recording. →1. Number 8. Press CLOSE when recording done. 2. Name 9. Move the joystick Up or Down to move the cursor to select 3. -
Page 29: Annex: Short-Cut Operations And Specifi- Cation Of Dome Device
Short-cut operation and specification of dome device Problem Description Possible Reason Solutions Remarks S.N. Check if the power cable is Power cable is connected improperly connected to power of AC24V After power on, Fault of power PCB of dome device Please follow the above Change the power PCB No motion and no image. -
Page 30: Short-Cut Operation Table
Short-cut operation table Operation Function description SONY CALL Save speed of Line Scan √ √ PRESET Run default Preset Tour √ √ CALL Enable Line Scan √ √ PRESET Save start of Line Scan √ √ PRESET Save end of Line Scan √... -
Page 31: Product Specifications
Product Specifications Dome type VSD-26IP Color system Pickup device 1/4"Exview HAD CCD Total pixels 795(H)X596(V) Effective pixels 752(H)X582(V) Scanning frequency H:15.625KHz/V:50.00Hz Horizontal Resolution Color:480Lines/B\W:570Lines Minimum illumination Color:0.5Lux/F1.6(50IRE) B\W:0.001Lux/F1.6(50IRE) Optic zoom 26X f=2.5～91mm(F1.6～F3.8) Digital zoom Angle of view(H) 42°(wide)～1.6°(tilt) Sync system Internal/External(V-LOCK) S/N ration >50db(AGC OFF) -
Page 32: Lightning Arresters And Surge Suppressors
Operation Humidity 0%～90% (without condensation) Supplied Power 24V～AC 2A 60Hz/50Hz Power consumption 3.6W Weight 230G Dimensions 55.3 X57.5 X 81.8mm ¤ Design and specifications are subject to change without notice. Lightning arresters and Surge Suppressors The product adopts TVS lightning proof technology to prevent from damage by lightning strike below 1500 W and impulse signals such as surge, but it is also necessary to abide by the following precautions to ensure electrical safety based on practical circumstances: Keep the communication cables at least 50 meters away from high voltage equipment or cables.