Table of Contents
Advertisement
Quick Links
A
WARNING
l
ALL RANGES CAN
TIP
l
INJURY TO PERSONS
COULD RESULT
l
INSTALL ANTI-TIP
DEVICE PACKED
WITH RANGE
l
SEE INSTALLATION
INSTRUCTIONS
Reference
Contents:
m
Before you start
q
1
Product dimensions
m
Cabinet dimensions/requirements
z
Gas supply
requrrements
a
-(61
Installation
steps
m-j
Gas conversions
'Back1
If range does not operate
;v
If you need assistance,'service
Back
Moving
the range
If you need assistance:
Check your Use and Care Guide for a toil-free
number
to call or call the
dealer from whom you purchased
this range. The dealer is listed in
the Yellow
Pages of your phone directory
under "Appliances
-
Household
-
Major -
'Service and Repair."
Call when you:
:I
Have questions
about range installation
or operation
2
Need to obtain the name and number
of an authorized
service company.
When you call, you will need:
;,-. The range model number.
z
The range serial number.
Both numbers
are listed on the model/serial
rating plate located on the
frame behind the broiler door.
Advertisement
Table of Contents
Related Manuals for KitchenAid GAS RANGE
Summary of Contents for KitchenAid GAS RANGE
- Page 1 Reference Contents: Before you start Product dimensions Cabinet dimensions/requirements Gas supply requrrements -(61 Installation steps Gas conversions ‘Back1 If range does not operate If you need assistance,‘service Back Moving the range If you need assistance: Check your Use and Care Guide for a toil-free number to call or call the dealer from whom you purchased...
-
Page 2: Anti-Tip Bracket
Important: Observe all governing codes and ordinances. all local This installation must conform with codes and ordinances. In the absence of local codes, installation must conform with American National Standard, National Fuel Gas Code ANSI 2223.1 - latest edition**. Proper installation is your responsibility. - Page 3 - A.G.A. design-certified flexible metal connector (4-5 feet) or rigid gas supply line as needed - Insulated pad or l/4” plywood if range is installed concrete/ceramic floors: over carpeting wood floor: 3/16” carbide-tipped masonry l/8” drill bit drill bit (Hammer may be needed for anchors.) combination wrench...
-
Page 4: Anti-Tip Bracket Installation
Plug power supply cord into grounded outlet Make proper gas connection Install anti- tip bracket Level range Replace or close broiler door Preparation Put on safety glasses and gloves. Do Not use oven door handle to lift or move the range. Injury Hazard Because of the weight and size of this range, two or more people are required to... -
Page 5: Gas Connection
check that Before moving range across floor, range is still on cardboard shipping base to Operating position protect floor covering. front leveling leg Carefully move range into final operating position. Check that Place rack in oven. Place level on rack, rear leveling leg is first side to side;... -
Page 6: Check Operation
Check operation You have just finished installing Check operation of cooktop Check operation of oven/broil burner your new range. To get the most efficient use from your range, read your Use & Care Guide. Open broiler door. Keep Installation Instructions Guide close to range for easy reference. -
Page 7: Natural Gas Conversion
Natural gas conversion Gas conversions (from Natural gas to L.P. gas; or orifice from L.P. gas to Natural gas) must be done by a qualified installer. w Complete installation sections A-C (Pages 3-4) before converting cook-top to Natural gas. Check that main gas supply line has been shut off and the power supply cord is disconnected. - Page 8 Remove and orifice spuds etches L.P. manifold L.F. R.F. R.R. L.R. Locate Natural gas orifice spuds in a literature package included with the range. Remove L.P. gas orifice spuds using a 3/8’ combination wrench. Install Natural gas orifice spuds to replace the L.P. gas orifice spuds. Place L.P.
-
Page 9: If You Need Assistance
It range does not operate: Moving the range: Check that the circuit breaker is not tripped When moving range, slide range onto cardboard or the house fuse blown. or hardboard to prevent damaging the floor covering. Check that the power supply cord is plugged into the wall receptacle.