Do not store any containers with flammable materials, such as spray cans, fire extinguisher refill cartridges etc. in the refrigerator. Maintenance and Cleaning ¥ Before cleaning, always switch off the appliance and disconnect from the electrical supply.
The walls of the refrigerator are equipped with runners so that shelves can be positioned as desired. D040 D338 (only for ERU 1472) For better use of space, the front half-shelves can lie over the rear ones (see fig.).
The door shelves (only for ERU 1472) To permit storage of food packages of various sizes the half tray can be adjusted in horizontal. To do this proceed as figure. For more thorough cleaning, the butter shelf and the bottle shelf can be removed by pulling them in the directon of the arrows, then refitting them in position.
Defrosting The refrigerator automatically defrosts every time the compressor stops. The water is discharged, via the pipe, into a tray located below the appliance, where it evaporates. Important To avoid defrost water overflowing and dripping onto the food in the fridge, periodically clean the water discharge hole (F) situated under the salad drawers.
When the appliance is not in use When the appliance is not in use for long periods, disconnect from the electricity supply, empty all foods and clean the appliance, leaving the door ajar to prevent unpleasant smells. Something not Working? Before contacting your local Service Force Centre check the following points.
Customer Care Department For general enquiries concerning your Electrolux appliance or for further information on Electrolux products, please contact our Customer Care Department by letter or telephone at the address below or visit our website at www.electrolux.co.uk...
Standard guarantee conditions We, Electrolux, undertake that if within 12 months of the date of purchase this Electrolux appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our option repair or replace the same FREE OF CHARGE for labour, materials or carriage on condition that: ¥...
NET CAPACITY (*)This figure is based on standard test results in accordance with European Standard EN153. Actual consumption will depend on how the appliance is used and where it is located. ERU 1472 DIMENSIONS POWER SUPPLY VOLTAGE AND FREQUENCY TOTAL POWER ABSORBED...
Page 11
Electrical Connection WARNING THIS APPLIANCE MUST BE EARTHED. The manufacturer declines any liability should this safety measure not be observed. If the plug that is fitted to your appliance is not suitable for your socket outlet, it must be cut off and the appropriate plug fitted.
Installation Warning IF YOU ARE DISCARDING AN OLD APPLIANCE THAT HAS A LOCK OR CATCH ON THE DOOR, YOU MUST ENSURE THAT IT IS MADE UNUSABLE TO PREVENT YOUNG CHILDREN BEING TRAPPED INSIDE. Depending upon the position which you choose for your appliance, you may wish to reverse the way in which the door opens.
Door reversal To reverse the opening direction of the door, proceed as shown in the figures: Attention After completion of the door reversing operation, check that the door gasket adheres to the cabinet. If the ambient temperature is cold (i.e. in Winter), the gasket may not fit perfectly to the cabinet.
Building-in Before carrying out any work, remove the plug from the power socket. Grid preparation Left door opening: Remove the left side (A) of the grid cutting it from the rear (see figure). DO002/2 Right door opening: Remove the right side (B) of the grid cutting it from the rear (see figure).
Page 15
2. Push the appliance into place. The plug socket necessary for connection of the appliance to the electricity supply should be positioned, so that the plug is not placed in the recess. 3. To adjust the height proceed as follows: - Loosen or tighten the two front feet.
Page 16
6. To mount the furniture door proceed as shown in the figures: clic UPPER PART OF KITCHEN FURNITURE PANEL LOWER PART OF KITCHEN FURNITURE PANEL clic...
7. Refit the covering strip. Fitting the plinth ¥ For an opening height dimension A=820 mm and a plinth height dimension a=100 mm, the plinth may be fitted without adjustments. The same applies to an opening height dimension B=870 mm and a plinth height dimension b=150 mm.