Page 4
Warning! Safety • Do not place the TV and/or remote control in the following environments: Instructions - Keep the product away from direct sunlight. - An area with high humidity such as a bathroom CAUTION - Near any heat source such as stoves and RISK OF ELECTRIC SHOCK DO NOT OPEN other devices that produce heat.
Page 5
• Ventilation • Disconnecting the Device from the - Install your TV where there is proper Main Power - The power plug is the disconnecting ventilation. Do not install in a confined space such as a bookcase. device. In case of an emergency, the power - Do not install the product on a carpet or plug must remain readily accessible.
Page 6
• Do not touch the end of the power LG Electronics. Accidental fire or electric cord while it is plugged in. You may be shock can occur. Contact your local customer electrocuted.
Page 7
• Use only an authorized attachments / • Moving - When moving, make sure the product accessories approved by LG Electronics. Otherwise, this may result in fire, electric is turned off, unplugged, and all cables shock, malfunction, or product damage.
Page 8
Preparing • Use a certified cable with the HDMI logo attached. • If you do not use a certified HDMI cable, • If the TV is turned on for the first time after the screen may not display or a connection it was shipped from the factory, initialization error may occur.
Page 9
Separate Purchase Wall Mounting Bracket (Depending on model) Make sure to use screws and wall mount Separate purchase items can be changed or bracket that meet the VESA standard. Standard modified for quality improvement without any dimensions for the wall mount kits are notification.
Page 10
Lifting and moving 55/65SK95* 55/65SK85* the TV 65SK81* 75SK81* 65SK80* 70/75UK65* 65UK75* 86UK65* Please note the following advice to prevent the TV from being scratched or damaged and for Model 65UK65* 70/75UK67* safe transportation regardless of its type and 65UK69* 86UK67* size.
Page 11
Mounting on the • When transporting a large TV, there should be at least 2 people. Table • When transporting the TV by hand, hold the TV as shown in the following illustration. 1 Lift and tilt the TV into its upright position on a table.
Page 12
Securing TV to the Wall • Do not apply foreign substances (oils, lubricants, etc.) to the screw parts when assembling the product. (Doing so may damage the product.) • If you install the TV on a stand, you need to take actions to prevent the product from overturning.
Page 13
When (optional parts), fix it carefully so as you do not use LG’s wall mount bracket, please not to drop. use a wall mount bracket where the device is • ...
Page 14
Connections Connect various external devices to the TV and switch input modes to select an external device. For more information of external device’s connection, refer to the manual provided with each device. Antenna/Cable • Do not use a sharp object when you detached the cable cover.
Page 15
Satellite dish HDMI Connect the TV to a satellite dish to a satellite • Supported HDMI Audio format : socket with a satellite RF cable (75 Ω). (Depending on model) (Depending on model) DTS (44.1 kHz / 48 kHz / 88.2 kHz / 96 kHz), DTS HD (44.1 kHz / 48 kHz / 88.2 kHz / 96 CI module kHz / 176.4 kHz / 192 kHz),...
Page 16
• If you connect a gaming device to the TV, use the cable supplied with the gaming Some USB Hubs may not work. If a USB device device. connected using a USB Hub is not detected, • In PC mode, there may be noise associated connect it to the USB port on the TV directly.
Page 17
You can simply operate the TV functions, using the button. To obtain the RS-232C external control setup information, please visit www.lg.com. Download and read the manual. (Depending on model) • Do not drop the product or let it fall over when connecting external devices.
Page 18
Adjusting the menu When the TV is turned on, press the button one time. You can adjust the Menu items using the button. Turns the power off. Changes the input source. Scrolls through the saved programmes. Adjusts the volume level. Using Remote Control (Depending on model) The descriptions in this manual are based on...
Page 19
* To use the button, press and hold for Moves to the previous or next more than 3 seconds. screen. Streaming Service buttons Connects to the Video Streaming Service. (POWER) Turns the TV on or off. (HOME) Accesses Home menu. Selects Radio, TV and DTV * (HOME) Shows the previous history.
Page 20
Using Magic Remote Control (Depending on model) The descriptions in this manual are based on the buttons on the remote control. Please read this manual carefully and use the TV correctly. When the message “Magic Remote battery is low. Please change the battery.” is displayed, replace the battery.
Page 21
* To use the button, press and hold for Displays the set-top box Home more than 3 seconds. menu. - When you are not watching via a set-top (POWER) Turns the TV on or off. box: the display changes to the set-top box You can turn your set-top box on or screen.
Page 22
Registering Magic Remote • Do not mix new batteries with old batteries. This may cause the batteries Control to overheat and leak. How to register the Magic • Failure to match the correct polarities Remote Control of the battery may cause the battery to burst or leak, resulting in fire, personal To use the Magic Remote, first pair it with your injury, or ambient pollution.
Page 23
Troubleshooting Abnormal Display • If the product feels cold to the touch, there may be a small “flicker” when it is turned on. Cannot control the TV with the remote control. This is normal, there is nothing wrong with • Check the remote control sensor on the product.
Page 24
Generated Sound • “Cracking” noise: A cracking noise that occurs when watching or turning off the TV is generated by plastic thermal contraction due to temperature and humidity. This noise is common for products where thermal deformation is required. • Electrical circuit humming/panel buzzing: A low level noise is generated from a high- speed switching circuit, which supplies a large amount of current to operate a...
Page 25
Specifications (Depending on country) Broadcasting Specifications Digital TV Analogue TV DVB-S/S2 PAL/SECAM B/G, Television DVB-C D/K, I system DVB-T SECAM L DVB-T2 DVB-S/S2 DVB-C DVB-T/T2 VHF III : 174 ~ 230 UHF IV : 470 ~ 606 Channel UHF V : 606 ~ 862 coverage 46 ~ 862 MHz 950 ~ 2,150...
Page 26
(Only LK59*, LK60*, LK61*A, 32LK615*) Wireless module(LGSWFAC71)Specifications Wireless LAN (IEEE 802.11a/b/g/n/ac) Frequency Range Output Power (Max.) 2,400 to 2,483.5 MHz 13 dBm 5,150 to 5,725 MHz 16.5 dBm 5,725 to 5,850 MHz (Not for EU) 10 dBm As band channels can vary per country, the user cannot change or adjust the operating frequency.
Page 27
In addition to the source code, all referred license terms, warranty disclaimers and copyright notices are available for download. LG Electronics will also provide open source code to you on CD-ROM for a charge covering the cost of performing such distribution (such as the cost of media, shipping, and handling) upon email request to opensource@lge.com.
Page 30
OWNER’S MANUAL EXTERNAL CONTROL DEVICE SETUP Please read this manual carefully before operating the set and retain it for future reference. www.lg.com...
Page 31
KEY CODES KEY CODES • This feature is not available for all models. Code Code Function Note Function Note (Hexa) (Hexa) CH +, PR + R/C Button List R/C Button CH -, PR - R/C Button Exit R/C Button Volume + R/C Button PIP(AD) R/C Button...
Page 32
(TV) (PC) • LGTV supports PL2303 chip-based (Vendor ID : 0x0557, Product ID : 0x2008) USB to serial converter RS-232C IN which is not made nor provided by LG. (CONTROL & SERVICE) (TV) (PC) • It can be purchased from computer stores that carry accessories for IT support professionals.
Page 33
EXTERNAL CONTROL DEVICE SETUP (TV) (PC) (TV) (PC) Phone jack Type RS-232C IN • You need to purchase the phone-jack to RS-232 cable required for the connection between the PC and (CONTROL & SERVICE) (PC) (TV) the TV, which is specified in the manual. RS-232C IN (CONTROL &...
Page 34
EXTERNAL CONTROL DEVICE SETUP Communication Parameters • Baud rate : 9600 bps (UART) • Stop bit : 1 bit • Data length : 8 bits • Communication code : ASCII code • Parity : None • Use a crossed (reverse) cable. Command reference list (Depending on model) DATA...
Page 35
EXTERNAL CONTROL DEVICE SETUP Transmission / Receiving Protocol Transmission [Command1][Command2][ ][Set ID][ ][Data][Cr] [Command 1] : First command to control the TV. (j, k, m or x) [Command 2] : Second command to control the TV. [Set ID] : You can adjust the [Set ID] to choose desired monitor ID number in option menu. Adjustment range in TV is 1 to 99.
Page 36
EXTERNAL CONTROL DEVICE SETUP * Commands may work differently depending on model and signal. 01. Power (Command: k a) Ack [d][ ][Set ID][ ][OK/NG][Data][x] ► To control Power *On or Off of the set. * In case of video mute on only, TV will display On Transmission[k][a][ ][Set ID][ ][Data][Cr] Screen Display(OSD).
Page 37
EXTERNAL CONTROL DEVICE SETUP Data Min : 00 to Max : 64 * (Depending on model) Ack [i][ ][Set ID][ ][OK/NG][Data][x] 14. Bass (Command: k s) 09. Tint (Command: k j) ► To adjust Bass. ► To adjust the screen tint. You can also adjust in the AUDIO menu.
Page 38
EXTERNAL CONTROL DEVICE SETUP Set ID = All = 00 5th Band 20(decimal) Data 00 & 01 = Channel Data is 10 = 00 0a Acknowledgement [v][ ][Set ID][ ][OK/NG][Data][x] Data 02 = Analog Antenna TV = 00 Result = ma 00 00 0a 00 * It depends on model, and can adjust when sound mode is EQ adjustable value.
Page 39
EXTERNAL CONTROL DEVICE SETUP Number Data 05 = Digital Antenna TV = 02 - 22 : Antenna TV (DTV) – Don’t Use Physical Total = ma 00 00 00 11 00 01 02 Channel Number - 26 : Cable TV (CADTV) - Don’t Use Physical 2.
Page 40
11 11 EXTERNAL CONTROL DEVICE SETUP 24. Input select (Command: x b) (Main Picture Input) ► To select input source for main picture. Transmission [x][b][ ][Set ID][ ][Data][Cr] Data X : don’t care 00 : DTV 01 : CADTV 02 : Satellite DTV 10 : ATV Ack [t][ ][Set ID][ ][OK][Data00][Data01][Data02] ISDB-BS (Japan)
Page 41
EXTERNAL CONTROL DEVICE SETUP 27. Auto Configure (Command: j u) (Depending on model) ► To adjust picture position and minimize image shaking automatically. It works only in RGB (PC) mode. Transmission [j][u][ ][Set ID][ ][Data][Cr] Data 01 : Run Auto Configure Ack [u][ ][Set ID][ ][OK/NG][Data][x]...