Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Makita DTWA260
Summary of Contents for Makita DTWA260
- Page 1 INSTRUCTION MANUAL Cordless Impact Wrench DTWA260 Read before use.
-
Page 2: Specifications
SPECIFICATIONS Model: DTWA260 Fastening capacities Standard bolt M14 - M20 High tensile bolt M10 - M16 Maximum fastening torque 260 N•m Torque range Approx. 40 - 170 N•m Square drive 12.7 mm No load speed (RPM) 0 - 2,800 min... -
Page 3: Declarations Of Conformity
Work area safety WARNING: Wear ear protection. Keep work area clean and well lit. Cluttered or WARNING: dark areas invite accidents. The noise emission during actual use of the power tool can differ from the declared val- Do not operate power tools in explosive atmo- ue(s) depending on the ways in which the tool is used spheres, such as in the presence of flammable especially what kind of workpiece is processed. - Page 4 Do not overreach. Keep proper footing and Keep cutting tools sharp and clean. Properly balance at all times. This enables better control maintained cutting tools with sharp cutting edges of the power tool in unexpected situations. are less likely to bind and are easier to control. Dress properly. Do not wear loose clothing or Use the power tool, accessories and tool bits jewellery.
- Page 5 Do not touch the terminals with any con- CAUTION: Only use genuine Makita batteries. ductive material. Use of non-genuine Makita batteries, or batteries that Avoid storing battery cartridge in a con- have been altered, may result in the battery bursting tainer with other metal objects such as causing fires, personal injury and damage. It will nails, coins, etc.
-
Page 6: Functional Description
Turn the tool off, and then turn it on again to To install the battery cartridge, align the tongue on the restart. battery cartridge with the groove in the housing and slip Charge the battery(ies) or replace it/them with it into place. Insert it all the way until it locks in place recharged battery(ies). with a little click. If you can see the red indicator as Let the tool and battery(ies) cool down. shown in the figure, it is not locked completely. If no improvement can be found by restoring protection To remove the battery cartridge, slide it from the tool system, then contact your local Makita Service Center. while sliding the button on the front of the cartridge. Fig.1 ► 1 . Red indicator 2. Button 3. Battery cartridge 6 ENGLISH... -
Page 7: Electric Brake
Electric brake 50% to 75% This tool is equipped with an electric brake. If the tool consistently fails to quickly stop after the switch trigger 25% to 50% is released, have the tool serviced at a Makita service center. 0% to 25% Lighting up the front lamp Charge the battery. - Page 8 NOTE: Use preset number as a guideline. To keep the fastening torque, number of impacts changes automatically according to remaining battery capacity. CAUTION: Always check the direction of NOTE: Use the Makita genuine USB cable to con- rotation before operation. nect your computer to the tool. Refer to the section CAUTION: Use the reversing switch only after "SPECIFICATIONS".
- Page 9 Changing the parameter setting on the tool (Field Setting mode) NOTICE: This function is available by default. If you have disabled the Field Setting mode on the computer, enable the Field Setting mode beforehand. Refer to the instruction manual of "Makita Industry Tool Settings" for how to configure. NOTICE: If the Field Setting mode is disabled, making settings on the tool is not available. When you press the setting button, the values set on the tool are displayed in order. NOTE: When the reversing switch lever is depressed in the clockwise rotation, the indicator shows the setting of clockwise rotation. When the reversing switch lever is depressed in the counterclockwise rotation, the indicator shows the setting of counterclockwise rotation.
- Page 10 Changing the torque level Press and hold the setting button until the indica- tor starts blinking. Example: When changing the torque level from 23 Set the rundown level. Every time you press the to 34 setting button, the indicator shows from "L1" to "L7" in a cycle. The highest sensitivity of the fastener seating is "L1" and "L7" is the lowest sensitivity.
- Page 11 This stands for the current setting of the longest workable time range. Measuring an actual operation (Self-diagnosis) NOTICE: This function is available by default. If you have disabled the Field Setting mode on the computer, enable the Field Setting mode beforehand. Refer to the instruction manual of "Makita Industry Tool Settings" for how to configure. You can measure the torque level and operating time of an actual operation by operating the tool. Measured torque level and time can be used for such as; • Reproducing a torque control technic of a well-skilled worker.
- Page 12 Overload protection The tool was over- Blinks in red and A series of short Remove the cause loaded and stopped. green alternatively. beeps of overload, and then restart the tool. Ask your local Makita Service Center for repair. 12 ENGLISH...
- Page 13 The motor has been Blinks in red and A series of short Ask your local locked. At this time, green alternatively. beeps Makita Service the tool does not Center for repair. work. Motor failure The tool detected a Blinks in red and A series of short Ask your local motor failure.
- Page 14 For impact socket with O-ring and pin ASSEMBLY Move the O-ring out of the groove in the impact socket and remove the pin from the impact socket. Fit the CAUTION: Always be sure that the tool is impact socket onto the square drive so that the hole in switched off and the battery cartridge is removed the impact socket is aligned with the hole in the square before carrying out any work on the tool.
-
Page 15: Installing Hook
The proper fastening torque may differ depending upon Installing hook the kind or size of the bolt, the material of the workpiece to be fastened, etc. Optional accessory The hook is useful to hang the tool. Install the hook to the holes on the tool body. Fig.17 NOTICE: When fastening small bolts, carefully Fig.16 adjust pressure on the switch trigger so that the bolt is not damaged. ► 1 . - Page 16 Fastening torque and torque level NOTE: This reference value is measured by the measurement conditions specified by Makita. NOTE: The actual value may differ according to circumstances of the fasteners, materials, and fastening method. Perform a test drive before actual work. N•m (kgf•cm) (2039) (1836) (1632) (1428) (1224) (1020) (816) (612) (408) (204) 1. Torque level 2. Fastening torque 16 ENGLISH...
-
Page 17: Maintenance
To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. OPTIONAL ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose. If you need any assistance for more details regard- ing these accessories, ask your local Makita Service Center. - Page 20 Makita Europe N.V. Jan-Baptist Vinkstraat 2, 3070 Kortenberg, Belgium Makita Corporation 3-11-8, Sumiyoshi-cho, Anjo, Aichi 446-8502 Japan 885A35-222 20230621...