hit counter script
Download
Share
Print this page
  1. Manuals
  2. Brands
  3. C.A. Technologies Manuals
  4. Paint Sprayer
  5. H2O-CPR-G
  6. Product information

C.A. Technologies H2O-CPR-G Product Information

Gravity feed spray gun
Hide thumbs
1
2
3
4

Advertisement

Quick Links

Download this manual
The H2O-CPR-G gun comes equipped with both a pressure reduced air cap 23-2101 and a HVLP air
cap 23-1301 for areas requiring HVLP compliance.
23-2101 - consumes 11 cfm at 29 psi gun inlet.
23-1301 - consumes 13.5 cfm at 29 psi gun inlet.
23-2101 pressure reduced air caps can be used with the 0.8 mm - 1.7 mm fluid orifices listed below.
23-1301 HVLP air caps can be used with the full range of fluid orifices listed below.
HVLP/PRESSURE REDUCED AIR CAP AND FLUID NOZZLE CHART
MODEL
FLUID TIP
AIR CAPS
NO.
RANGE
23-2101
CPR
0.8 - 1.7
(Pressure
Reduced)
H2O-CPR-G
23-1301
0.8 - 2.2
(HVLP)
Actual fluid nozzle and air cap combinations are determined by application (see application chart page 4)
*Note: Air cap test gages are available to confirm HVLP compliance.
*Gun inlet pressures may vary as required by application
Coating Atomization Technologies 337 South Arthur Avenue, Louisville CO 80027 Phone: 888.820.4498, Fax: 303.438.5708
*MAX GUN
FAN
INLET PRESS.
CONTROL
FOR HVLP
29*
60-1504 (S)
29*
www.spraycat.com
H2O-CPR-G
GRAVITY FEED SPRAY GUN
SCFM @
STANDARD
MAX GUN
IN CAT
INLET
PACK
11
G, PPS
G, PPS
G, PPS
13.5
PRODUCT INFORMATION
AVAILABLE FLUID
NOZZLES TIPS
marking on needle
33-0208 0.8mm (.022")
33-0210 1.0mm (.040")
33-0212 1.2mm (.046")
33-0213 1.3mm (.052")
33-0214 1.4mm (.055")
33-0215 1.5mm (.059")
33-0217 1.7mm (.070")
33-0219 1.9mm (.075")
33-0222 2.2mm (.086")
H2O-CPR-G
H2O-CPR-G-PPS
NEEDLES /
40-1308 (308)
40-1310 (310)
40-1312 (312)
40-1313 (313)
40-1314 (314)
40-1315 (315)
40-1317 (317)
40-1319 (319)
40-1322 (322)

Advertisement

loading

Related Manuals for C.A. Technologies H2O-CPR-G

Summary of Contents for C.A. Technologies H2O-CPR-G

  • Page 1 GRAVITY FEED SPRAY GUN PRODUCT INFORMATION The H2O-CPR-G gun comes equipped with both a pressure reduced air cap 23-2101 and a HVLP air cap 23-1301 for areas requiring HVLP compliance. 23-2101 - consumes 11 cfm at 29 psi gun inlet.
  • Page 2 H2O-CPR-G Operation and Maintenance Instructions for Spray Guns Operation 1. Connect air supply hose at handle of gun. 2. Screw the paint cup onto the gun’s gravity feed fluid inlet. 3. Fluid flow can be controlled using the fluid control knob, this restricts flow by limiting needle travel. It is best to control fluid flow by proper selection of fluid orifice size and use the fluid control knob to “fine tune flow rate”.
  • Page 3 HVLP AIR CAP TEST GAGES 23-1301-G H2O-CPR-G ITEM NO. PART NO. DESCRIPTION ITEM NO. PART NO. DESCRIPTION See Air Cap Chart Air Cap** 60-2101 Trigger See Air Cap Chart Fluid Tip** 60-1520 Air Valve Assembly 33-1202 Fluid Nozzle Body 60-302...
  • Page 4 FLUID NOZZLE / AIR CAP SELECTION CHARTS H2O-CPR-G Series - Gravity Feed Guns H2O-CPR-G HVLP/PRESSURE REDUCED SPRAY GUN FLUID ORIFICE x MAXIMUM MATERIAL TYPE AIR CAP PATTERN WIDTH Very Thin 0.8 mm x 2101 or 1301 23-2101 13" 23-2101 11 CFM less than 16 sec.