Related Manuals for Miele PW 6068 Plus
Summary of Contents for Miele PW 6068 Plus
- Page 1 Operating Instructions Washer PW 6068 Plus en - US To prevent accidents and machine damage read these instructions before installation or use. M.-Nr. 10 196 550...
-
Page 2: Table Of Contents
Contents IMPORTANT SAFETY INSTRUCTIONS....... . . 3 Guide to the washer..........6 Control panel . -
Page 3: Important Safety Instructions
Check with a qualified electrician if you certain conditions it may be possible for are in doubt as to whether the an installation in these applications. appliance is properly grounded. Please contact the Miele Technical Ser- vice Dept. with specific requirements. - Page 4 Do not repair or replace any part of the appliance or attempt any servicing If the power cord is damaged it unless specifically recommended in must only be replaced by a Miele Ser- these operating instructions. vice technician with a genuine Miele power cord.
- Page 5 IMPORTANT SAFETY INSTRUCTIONS Do not add gasoline, dry-cleaning solvents, or other flammable or Do not allow children to play on or in explosive substances to the wash the appliance. Close supervision is water. These substances give off necessary when the appliance is used vapors which could ignite or explode.
-
Page 6: Guide To The Washer
Guide to the washer Control panel a Display* d PC Indicator/Optical interface See the following pages for more Allows a service technician to check information and update the wash programs b Direct select buttons e Jog shuttle To select a wash program directly. Turn to select menus You can also save a "Favorite"... - Page 7 Guide to the washer Display function Display contents will vary with program offering. Main menu Cottons Uni. 140°F Program selection... 2 Wrinkle-free 104°F Settings F... 3 Delicates 104°F 12:00 4 Woollens H 86°F The display shows the main menu (with default settings). "Program selection"...
- Page 8 Guide to the washer Menu Program selection Program BackA selection Cottons Hygiene Cottons Uni. Minimum Iron All pre-set programs can be selected with the jog shuttle. Depending on the direction the jog shuttle is turned the highlighter moves up or down. The arrows e- at the right side of the display show that more selections are available.
-
Page 9: Before Using For The First Time
Press again to save the time The Welcome screen shows when the of day. washer is turned on for the first time: "Miele Professional Welcome". First wash ^ Select the program "Cottons Uni." The Welcome screen will not show after the washer has been running for and confirm. -
Page 10: Use
1. Sort the laundry General tips – Dark fabrics often bleed the first few times they are washed. They should be washed separately several times before being included in a mixed load. – Remove any lead weights or strips from curtains before washing. –... - Page 11 2. Load the washer 3. Select a program ^ Open the drum door using the a Two program selection possibilities: button. – Select a "Favorite" by pressing the The drum light comes on. respective direct select button. ^ Load the laundry loosely into the –...
- Page 12 4. Adding detergent Use detergent according to the laundry soiling and water hardness. Too little detergent may cause: – ineffective cleaning of laundry; fabrics may become gray and stiff over time. – grease stains on the laundry. – hard water deposits on the heating element.
- Page 13 i Detergent for "Heavy Soil" Using powder detergent ^ Only add detergent ( Liquid detergent inserts come already of the total amount recommended) to the i inserted in the detergent compartments. To use powder compartment, if the "Heavy Soil" detergent remove the inserts. option is selected.
- Page 14 5. Starting a program 6. At the end of a program "Start" flashes when a program can be The anti-crease program starts when started. the laundry is not immediately removed from the washer after the program end. ^ Press the "Start" button. "Anti-crease"...
-
Page 15: To Cancel A Program
To cancel a program Note: A program can be canceled any time Once the program has started the after the program start. washer cannot make adjustments to the load size. After adding or removing ^ Press the G button "Cancel". laundry, the washer will default to the The wash water will be drained away. -
Page 16: Program Guide
Program guide Programs may vary. Cottons Hygiene 203°F to 158°F (95°C to 70°C) max. 14.3 lbs (6.5 kg) Items Items made from cotton and linen, i.e. bed linens, baby clothing, underwear Detergent Universal detergent Extras Pre-wash, Starch Stop, Rinse Stop, Intensive*, Water plus* Note The spin speed (1400 rpm) cannot be changed. - Page 17 Program guide Quick wash 104°F (40°C) to cold max. 7.7 lbs (3.5 kg) Items Small loads of lightly soiled items, which can be washed in "Cottons Uni." Detergent Universal or color detergent Extras Rinse Stop Woollens 104°F (40°C) to cold max.
- Page 18 Program guide Denim 104°F (40°C) to cold max. 7.7 lbs (3.5 kg) – Before washing denim items turn them inside out. – Denim items bleed during the first few washes. Wash dark and light colored items separately. Detergent Liquid color detergent Extras Rinse Stop Toweling 203°F to 140°F (95°C to 60°C)
- Page 19 Program guide Additional programs The following programs can be added in "Settings - Supervisor level" when activated by Technical Service. Kitchen linen 203°F to 140°F (95°C to 60°C) max. 14.3 lbs (6.5 kg) Items Kitchen linens made from cottons and linen fabrics, i.e. chef jackets and pants, towels, rags Use the "Pre-wash"...
- Page 20 Program guide Pillows 203°F to 104°F (95°C to 40°C) 1 queen (80x80 cm) or 2 twin size pillows (40x80 cm) Items Washable pillows with a filling of feathers, down or synthetics. Regard the fabric care label! Detergent Liquid detergent Extras Rinse Stop Outerwear 104°F (40°C) to cold max.
- Page 21 Program guide Disinfection programs max. 14.3 lbs (6.5 kg) Items Items made of cotton or mixed fabrics. Note For different requirements with a temperature selection of 185°F [85°C (thermal)] to 104°F [40°C (chemothermal)] with the respective holding times. Detergent Use a detergent for disinfection and chemothermal disinfection. Regard the temperature level recommended on the packaging.
-
Page 22: Program Sequence
Program sequence *Programs may vary depending on the offerings of your machine. Main wash Rinse Spin Water Wash Water Rinses Rinse spin Final spin level rhythm level Cottons Hygiene Cottons Uni. Minimum iron Delicates – Quick wash Woollens Silks – Shirts –... - Page 23 Program sequence The washer is equipped with an Special features in the program electronic control which determines the sequence: load size automatically. The washer determines the required water Anti-crease consumption for each load depending The drum continues to turn up to on quantity and water absorbency of 30 minutes after the program ends to the laundry.
-
Page 24: Spin Speed
Spin speed Maximum spin speeds Rinse spin The laundry is spun after the main wash Program and between the rinse cycles. Cottons Hygiene 1400 Reducing the final spin speed will also Cottons Uni. 1400 reduce the rinse spin speeds. Minimum iron 1000 Delicates Without final spin... -
Page 25: Extras
Extras The basic wash programs can be enhanced with "Extras". Accessing the submenu "Extras" Cottons Uni. 140°F 1400 rpm Duration 0:47 h Extras Timer Y Back A ^ Press the direct select button D. The submenu "Extras" shows. Selecting Extras Cottons Uni. - Page 26 Extras Rinse Stop The washer stops after the last rinse, the laundry remains soaking in water. This will prevent wrinkles if the laundry is not removed immediately at the end of the wash program. Intensive* For laundry with normal to heavy soiling or stains. The total time for the wash program will be extended.
-
Page 27: Timer
Timer The timer option allows you to select the program end time. The program start can be delayed from 30 minutes to 24 hours. Select the submenu Timer Cottons Uni. 140°F 1400 rpm Duration 0:47 h Extras Timer Y Back A ^ Press the direct select button E. -
Page 28: Favorites
Favorites The washer has the option to save the most used wash programs on the direct select buttons. The option "Save" must be selected in "Settings - Supervisor level". Contact Technical Service for access to this level. Selecting/Changing a Favorite Main menu Cottons Uni. - Page 29 Favorites – Select a program Program BackA selection Cottons Hygiene Cottons Uni. Minimum iron ^ Select the desired program with the jog shuttle and confirm. The basic menu shows again. – Selecting a temperature Cottons Uni. °F 1400 rpm Temperature cold - 140°F ^ Select the desired temperature with the jog shuttle and confirm.
- Page 30 Favorites Saving a Favorite The basic menu shows all selected components. Cottons Uni. 140°F 1400 rpm Pre-wash Duration 0:56 h Extras Timer Y Save Back A ^ Press the direct select button F. Assigning a direct select button Cottons Uni. 140°F 1400 rpm Pre-wash...
-
Page 31: Detergent
Detergent Water hardness Only use laundry detergent formulated for front loading washing machines. Hardness Water Water Water level quality hardness hardness For wool and wool blend fabrics use a in gpg in mmol/l detergent formulated for wools. (also German hardness in Follow instructions on the detergent °d) packaging for the correct use and... - Page 32 Detergent Fabric softener, liquid starch Automatic dispensing of fabric softener or liquid starch Fabric softener added to the wash program will make fabrics feel softer and will reduce static cling in the dryer. Liquid starch is a synthetic starch wash used to give fabrics some stiffness.
- Page 33 ^ Add starch to the i compartment. dosage system. A conversion kit is necessary which can be purchased ^ Select the program "Starch". from Miele. ^ Press "Start". Starching with Starch Stop ^ Prepare and dispense the amount of starch recommended on the packaging.
-
Page 34: Cleaning And Care
Cleaning and Care ^ Pull out the detergent drawer as far Before cleaning the appliance, as it will go. Press the red release disconnect the power supply by lever down and pull the drawer out of unplugging the unit or manually the machine. - Page 35 Cleaning and Care Cleaning the niche of the detergent Cleaning the liquid detergent inserts drawer ^ Push the insert apart and remove the ^ Using a bottle brush remove any siphon for easy cleaning. detergent or lime deposits from the water inlet valves at the top of the detergent drawer niche.
-
Page 36: Cleaning The Inlet Hose Filter
Cleaning and Care Cleaning the inlet hose filter Cleaning the filter in the inlet valve ^ Using pliers carefully loosen and The washer has two water inlet filters to protect each inlet valve. Check and remove the plastic hose connector clean these filters every 6 months. -
Page 37: Frequently Asked Questions
Frequently asked questions Repairs to electrical appliances must only be carried out by a qualified and trained person in accordance with local and national safety regulations. Repairs and other work by unqualified persons could be dangerous. The following section will help you avoid placing a service call by identifying issues you may encounter while operating the machine: A wash program cannot be started Problem... -
Page 38: General Problems With The Washer
Frequently asked questions General problems with the washer Problem Possible cause Solution The washer shakes – The four feet are not – Level the machine (see during the spin cycle. resting evenly on the Installation Instructions). floor. – The floor is not –... - Page 39 Frequently asked questions Poor wash results Problem Possible cause Solution The laundry does Liquid detergents do not – Use powder detergent not get clean with contain bleaching agents. containing bleach. liquid detergent. Fruit, coffee and tea (Be sure this is suitable stains may not be according the fabric care removed.
- Page 40 Frequently asked questions The door will not open when the "a" button is pressed Problem Solution The washer has no Insert the plug into the outlet and ensure the circuit power. breaker has not tripped. Power failure To open the drum door, see "Frequently asked questions - Opening the drum door during a power failure...".
-
Page 41: Opening The Door During A Power Failure Or When The Drain Is Blocked
Frequently asked questions Opening the door during a Machines with a drain pump power failure or when the drain If the main drain hose is clogged, water is blocked will be retained in the machine (max. 6.5 gal [30 l]). Disconnect the machine from the power supply. - Page 42 Frequently asked questions Once the flow of water stops: Open the drum door Always make sure the drum is stationary before reaching in to remove laundry. A moving drum is extremely dangerous. ^ Remove the lint trap lid. ^ Remove any foreign objects or lint from the filter.
- Page 43 Frequently asked questions Machines with a drain valve Open the drum door Always make sure the drum is stationary before reaching in to remove laundry. A moving drum is extremely dangerous. ^ Press the lever for the emergency drain down and hold until you hear no more water running out.
-
Page 44: After Sales Service
Miele will provide information when such possibilities become available. Both can be found on the data plate visible above the front glass on the Optional accessories inside of the door. Optional accessories are available through your Miele dealer or Miele. -
Page 45: Installation Instructions
Installation Instructions To prevent accidents and machine damage read these instructions before installation or use. -
Page 46: Installation
Installation Front view a Water intake hose hot f Access panel to drain filter, drain pump and emergency door release b Water intake hose cold g Height adjustable feet c Control panel h Stand d Detergent dispenser drawer i Fixing bracket (for concrete stand) e Drum door... - Page 47 Installation Rear view a Lid with transport grips d Shipping struts with rotary protectors b Mounting for: e Water intake hose (cold) f Water intake hose (hot) – Water intake hose g Drain hose for drain pump – Drain hose h Drain hose for drain valve –...
-
Page 48: Installation Site
Installation ^ Install the unit on a 27 Installation site " x 23 " x " (70 x 60 x 3 cm) plywood The appliance is not intended to be base. Ideally the base should be mounted in a wall or other vertical large enough to span several joists surface of a building or cabinet. - Page 49 Installation ^ Turn the left shipping strut ^ Turn the right shipping strut counterclockwise 90° with the clockwise 90° with the enclosed enclosed combination wrench. combination wrench. ^ Pull out the shipping strut out. ^ Pull the shipping strut out.
-
Page 50: Installing The Shipping Struts
Installation Movement of the washer without the shipping struts in place should be kept to a minimum. The shipping struts should be stored on the back of the washer for future use. They must be reinstalled before moving the machine. Installing the shipping struts ^ Reinstall the struts by reversing the installation procedure. -
Page 51: Leveling The Washer
Installation Leveling the washer Adjust the four leveling feet The washer is leveled by adjusting the four feet. The machine is boxed with the feet completely screwed in. To ensure smooth operation the washer must be level. Failure to level the machine can result ^ Turn the locking nut, 2, counter- in increased water and energy clockwise with the enclosed... - Page 52 The supplied sticker must be affixed at or near by the washer: "This washer must be connected to the power supply to open the drum door. Do not use force to open the door." * Available from your Miele dealer or Miele.
-
Page 53: Water Connection
Extension hoses (8’ 2" or 13’ [2.5 m or line by a qualified plumber. 4 m]) may be obtained from Miele. The water pressure must be between 14.5 -145 psi (1 -10 bar). If the water... - Page 54 Installation Hot water connection If the washer is not to be installed for hot water connection, the settings "Main Connecting the machine to a hot water wash", "Pre-wash" and "Rinse" must be supply will lead to low electrical adjusted respectively. The hot water consumption during hot water intake hose must be removed.
-
Page 55: Drainage
16’ 5" (5 m). The hose There are two drainage extras for this extension can be purchased from your machine: Miele dealer or Miele. Drain valve The machine is drained with a motorized drain valve. A connection can be made to an on-site floor drain (gully with an air gap) on an angle. -
Page 56: Electrical Connection
Installation Electrical connection This installation should be performed by an experienced and qualified technician, in accordance with local codes and regulations. The washer comes with a power cord and NEMA L6-30 plug. The machine is supplied as standard for connection to a 208/240 V, 60 Hz, 30 A, 2-phase electrical supply. -
Page 57: Technical Data
Technical Data Height 33 7/16" (85 cm) Width 23 7/16" (59.5 cm) Depth 28 3/8" (72 cm) Depth with the door open 44 1/8" (112 cm) Weight 240 lbs (109 kg) Maximum floor load 613 lb [2778 Newton (approx. 278 kg)] Capacity 14.3 lbs (6.5 kg) dry laundry Fuse rating... -
Page 58: Help To Protect The Environment
Help to protect the environment Disposal of the packing Disposal of an old appliance materials Old appliances may contain materials that can be recycled. Please contact The cardboard box and packing your local recycling authority about the materials protect the appliance during possibility of recycling these materials. - Page 59 Menu Settings J to adjust standard settings The washer controls can be adjusted to changing demands through the settings menu.
-
Page 60: Settings J
Settings J Opening the menu Settings Cottons Uni. 140°F Program selection... 2 Minimum iron 104°F Settings F... 3 Delicates 104°F 12:00 4 Woollens H 86°F ^ Select the "Settings" J in the main menu and confirm by pressing the jog shuttle. Selecting Settings Settings BackA... - Page 61 Settings J Language J Time of day The display contents can be shown The selection allows the clock to be in different languages. shown as 24 hours, 12 hours or not at all. The time of day is also set The displayed language can be set in here.
- Page 62 Settings J Contrast / Brightness Memory The contrast / brightness of the The Memory function remembers the display can be set at ten different addition of an extra feature to a levels. program, a change in spin speed or temperature the next time that The contrast / brightness changes im- program is selected.
-
Page 63: Settings - Supervisor Level
Settings - Supervisor level The menu Settings - Supervisor level must be activated by Technical Service. The menu "Settings" (except Languages J) is locked with a code to prevent unwanted access. Selecting Settings Settings BackA Language F Supervisor level ^ Select "Supervisor level" and confirm. Settings BackA Supervisor level... - Page 64 Settings - Supervisor level Confirming the code 0 0 0 Confirm code Back A ^ Confirm the entered code. Code accepted Menu opened The user is now in the "Supervisor level". The previously described settings and all of the following settings can be changed.
- Page 65 Settings - Supervisor level Language J Favorites The display contents can be shown The 12 programs of the basic menu in different languages. for the operating variation "WS-KW-Button + Logo" can be The fixed default language can be set configured (only in conjunction with in the submenu "Language J".
- Page 66 "Controller option "WS-KW-Buttons + screen can be shown before the Logo"). main menu or after the end of a wash program. The Miele Professional logo is shown by default. Three selections are available: – National: no additional welcome screen (default).
- Page 67 Settings - Supervisor level Intensive Water plus Save You can select if the extras The option "Save" can be shown in "Intensive" and "Water plus" are the basic menu. The function "Save" shown in the menu "Extras". is needed to save, for example, the favorite wash programs on the direct The option is factory set to "off".
- Page 68 Settings - Supervisor level Pre-wash water Rinse water The water type for the pre-wash can The water type for the rinse in the be selected (except for the program programs "Cottons Hygiene", "Woolens, Silk, Curtains and "Cottons Uni.", "Minimum iron", Proofing").
- Page 69 Settings - Supervisor level Water level Cottons Pre-wash duration Cottons The program "Cottons Hygiene" and The programs "Cottons Hygiene" "Cottons Uni." allows you to increase and "Cottons Uni." allow to extend the water level for the main wash. the wash time for the pre-wash. This option is set to "Block Parameter"...
- Page 70 Settings - Supervisor level No. of programs Disinfection Additional programs can be added Special disinfection programs can to the program selection. be added. 0 Additional programs (default) 0 Additional programs (default) 4 Additional programs ("Table linen", 4 Additional programs "Pillows", "Curtains" and "Kitchen (Thermal disinfection linen") 15 min/185°F (85°C),...
- Page 71 Settings - Supervisor level 2nd pre-wash Kitchen linen Pre-rinse Cottons The program "Kitchen linen" allows The programs "Cottons Hygiene" an additional pre-wash. and "Cottons Uni." allows you to add a pre-rinse. ^ Add the detergent for the additional pre-wash directly in the drum. This option is set to "off"...
- Page 72 Settings - Supervisor level Spin free of charge External dispenser When operated by a coin The washer is set for connection to mechanism, the program "Spin" can an external dispensing system. To be activated free of charge. use the external dispensing system the setting must be adjusted/set This option is set to "off"...
- Page 73 Settings - Supervisor level Controls GB-with speed dial button (adjusted program allocation). The "Operating variant" of the machine can be adjusted. GB-with KW-buttons Sluice (adjusted program allocation). Caution: When selecting WS-KW-Buttons + Logo "WS-KW-Buttons simple" or (special operating variant for "WS-KW-Buttons + Logo"...
- Page 76 Alteration rights reserved / 4015 M.-Nr. 10 196 550 / 00 INFORMATION IS SUBJECT TO CHANGE. PLEASE REFER TO OUR WEBSITE TO OBTAIN THE MOST CURRENT PRODUCT SPECIFICATIONS, TECHNICAL & WARRANTY INFORMATION.