Advertisement
Quick Links
thank you for purchasing a sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
instruction
manual
1. saFety
This stand is intended to provide partial support of vehicle components during removal and installation.
9
do not use if damaged. ensure the exhaust stand is in good order and condition.
8
do not make alterations to the product.
8
ensure you familiarise yourself with the product before use.
8
Adequately support the vehicle before starting repairs.
9
only use on a hard level surface. do not use on soft ground or tarmacadam. use on concrete only.
9
do not exceed rated capacity (750kg).
8
do not use this product as an axle stand.
8
do not use to support or stabilise vehicle.
8
Centre load on saddle.
9
do not attempt to use this product for a task it is not designed to perform.
8
2.
introduction
i
Screw adjustment with easy-to-use spinner nut and ball bearing thrust race for smooth operation. Removable base for easier storage. Adjustable
over a 668mm range.
3.
speciFication
i
model no: ........................................................................eS750.V3
Capacity: ................................................................................750kg
min. height: ........................................................................ 1364mm
max. height: ....................................................................... 2032mm
4.
asseMbly
i
refer to parts diagram
4.1.
Unpack the product and check contents. Should there be any damaged or missing parts contact your supplier immediately.
4.2.
Screw the upright support post (9) into the base (16).
4.3.
Insert the upright post (8) into the upright support post (9) and align the holes in both of them.
4.4.
Slide a washer (15) over the stop pin (12) and insert the stop pin (12) through the upright post and support assembly to join them
together.
4.5.
Place washer (15) over the protruding end of the stop pin and retain the whole assembly by inserting the retaining pin (14) through the
end of the stop pin.
4.6.
Thread the handle (5) onto the top of the threaded rod (7) and wind it clockwise, a short distance down the rod.
4.7.
Place the saddle (3) over the top of the threaded rod (7) and retain it with screw (4).
4.8.
Place the bearing (6) on top of the upright post (8) and hold it there.
4.9.
Insert the bottom end of the threaded rod (7) through the bearing (6) and into the top of the upright post (8).
4.10.
lower the threaded rod (7) into the upright post (8) until it stops.
4.11.
The exhaust stand is now ready for use.
5. operation
Warning! before use ensure you have read, understood and apply section 1 "safety instructions".
‰
5.1.
positioning stand beneath exhaust systeM
Warning! Before use ensure the exhaust weight and size does not exceed the capacity of the stand.
‰
Warning! ensure the vehicle from which the exhaust is to be removed is correctly positioned, handbrake applied, and raised to allow
‰
the exhaust stand to be positioned correctly.
5.1.1.
ensure there are no other persons around or under the vehicle.
5.1.2.
ensure saddle is in its lowest position and centrally position stand beneath vehicle's exhaust.
5.1.3.
Rotate handle in a clockwise direction to raise the saddle.
5.1.4.
When saddle is just beneath the exhaust re-adjust alignment if necessary to centralise the saddle.
© Jack Sealey limited
750kg capacity exhaust support stand
es750.V3
model no:
Original Language Version
eS750.V3 | Issue 1 05/08/19
Advertisement
Related Manuals for Sealey ES750.V3
Summary of Contents for Sealey ES750.V3
- Page 1 Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
- Page 2 Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim. sealey group, kempson Way, suffolk business park, bury st edmunds, suffolk. ip32 7ar 01284 757500 01284 703534 sales@sealey.co.uk...