hit counter script
Pioneer GM-ME500X1 Owner's Manual
Pioneer GM-ME500X1 Owner's Manual

Pioneer GM-ME500X1 Owner's Manual

Marine mono amplifier

Advertisement

Quick Links

MARINE MONO AMPLIFIER
AMPLIFICATEUR MONO MARIN
GM-ME500X1
English
Français

Advertisement

Table of Contents
loading

Summary of Contents for Pioneer GM-ME500X1

  • Page 1 MARINE MONO AMPLIFIER AMPLIFICATEUR MONO MARIN GM-ME500X1 English Français...
  • Page 2 Before you start If you experience problems Thank you for purchasing this PIONEER product Should this product fail to operate properly, please contact your dealer or nearest author- To ensure proper use, please read through this ized Pioneer Service Station.
  • Page 3: Before You Start

    Before you start BE SURE TO OBSERVE THE FOLLOWING Always use a fuse of the rating prescribed. GUIDELINES: The use of an improper fuse could result in Do not turn up the volume so high that you overheating and smoke, damage to the pro- can t hear what s around you.
  • Page 4 Before you start Attach a cover or cap to the terminals, and If a DC voltage is applied to the speaker prevent them from getting wet. output terminal. The POWER/PROTECT indicator will turn red Install the amplifier in a dry and well-venti- lated environment, where other electrical ap- and the output will be muted in the situations pliances installed on the boat will not interfere...
  • Page 5: Setting The Unit

    Preout level: 2 V (Standard: 500 mV) (standard output of 500 mV), set to the NORMAL position. For use with an RCA equipped Pioneer stereo, with maximum output of 4 V or more, adjust level to match that of the stereo output.
  • Page 6: Connecting The Units

    Setting the unit Connecting the units Relationship between amplifier gain Connection diagram and head unit output power If amplifier gain is raised improperly, this will simply increase distortion, with little increase in power. Signal waveform when outputting at high volume using amplifier gain control 1 Battery wire (sold separately) The maximum length of the wire be-...
  • Page 7: Before Connecting The Amplifier

    Connecting the units 9 Connecting wire with RCA pin plugs (sold se- Install and route the separately sold battery parately) wire, ground wire, speaker wires and the am- a Amplifier with RCA input jacks (sold sepa- plifier as far away as possible from the anten- rately) na, antenna cable and tuner.
  • Page 8: Connections When Using The Speaker Input Wire

    Connecting the units When connecting to two speakers Notes The output from two speakers is the same as If speaker input wires from a headunit are that of one speaker. connected to this amplifier, the amplifier will automatically turn on when the headunit is turned on.
  • Page 9 Connecting the units Always use the recommended battery and Use wire cutters or a utility knife to strip the end of the battery wire, ground ground wire, which is sold separately. Con- wire and system remote control wire to ex- nect the battery wire directly to the boat pose about 10 mm (3/8 in.) of the end of battery positive (+) terminal and the...
  • Page 10: Installation

    Connecting the units Installation Connecting the speaker output Before installing the amplifier terminals WARNING Use wire cutters or a utility knife to To ensure proper installation, use the supplied strip the end of the speaker wires to ex- parts in the manner specified. If any parts pose about 10 mm (3/8 in.) of wire and other than those supplied are used, they may then twist the wire.
  • Page 11 Installation Example of installation on the chassis Place the amplifier in the desired instal- lation location. Insert the supplied tapping screws (4 mm × 18 mm (5/32 in. × 3/4 in.)) into the screw holes and push on the screws with a screwdriver so they make an imprint where the installation holes are to be located.
  • Page 12: Additional Information

    Additional information Specifications Power output ......300 W RMS × 1 Channel (at 14.4 V, 4 W, 20 Hz to 240 Hz and ≦ 1 % THD+N) Power source ......14.4 V DC (10.8 V to 15.1 V allowable) 500 W RMS × 1 Channel (at 14.4 V, 2 W, 100 Hz and ≦...
  • Page 13 TEL: 65-6378-7888 PIONEER ELECTRONICS AUSTRALIA PTY. LTD. 5 Arco Lane, Heatherton, Victoria, 3202 Australia TEL: (03) 9586-6300 PIONEER ELECTRONICS DE MÉXICO S.A. DE C.V. Blvd.Manuel Ávila Camacho 138, 10 piso Col.Lomas de Chapultepec, México, D.F. 11000 TEL: 52-55-9178-4270 FAX: 52-55-5202-3714 先鋒股份有限公司...

Table of Contents