hit counter script
Download
Share
Print this page
Lenovo S660 Service Manual
  1. Manuals
  2. Brands
  3. Lenovo Manuals
  4. Cell Phone
  5. S660
  6. Service manual

Lenovo S660 Service Manual

Hide thumbs Also See for S660:

Advertisement

Quick Links

Download this manual
Company confidential
Lenovo S660 Service Manual
Publisher：NJD HW Team
Date：2014.02.28

Advertisement

loading

Related Manuals for Lenovo S660

Summary of Contents for Lenovo S660

  • Page 1 Company confidential Lenovo S660 Service Manual Publisher：NJD HW Team Date：2014.02.28...

  • Page 2: Function Block

    Function Block Company confidential...
  • Page 3 M/B Top Placement #1 Receiver Audio Jack crystal SKY77593 MT6166 FLASH Backlig ht IC MT6582 MT6627 Charge MB to SB connector Company confidential...
  • Page 4 M/B Bottom Placement #2 Connector Sensor G-Sensor Connector Mic 2 Audi o PA BACK UP BATTERY Camera Connector DUAL SIM CONNECTOR crystal TF CARD CONNECTOR connector MT6323 Battery connector Company confidential...
  • Page 5 BB Common Question • BB-1 Power on failure (無法開機) • BB-2 Firmware update failure (無法更新軟件) • BB-3 Charging failure (無法充電) • BB-4 SIM Card identified error (SIM卡無法識別) • BB-5 LCD display error (畫面無法顯示或顯示異常) • BB-6 Sensor function failure (感測器不良) • BB-7 Touch Panel function failure (無法觸屏) •...
  • Page 6 BB-1 Can not power on (無法開機) (1/3) • 1. Check if battery power level is low (確認電池是否有電?) – VBATT (TP09 > 3.6V) • 2. Check if J802 soldering condition is good (確認J802吃錫狀況是否正常?) • 3. Check if power button is functional (確認開機鍵是否正常?) –...
  • Page 7 BB-1 Can not power on (無法開機) (2/3) • 5. Please check whether MT6323 voltage is normal (請確認MT6323周圍電壓是否 正常?) – VPROC_PMU should be between C134 (0.9V~1.1V) – VSYS_PMU should at R373 (1.8V) VPROC_PMU VSYS_PMU Company confidential...
  • Page 8 BB-1 Can not power on (無法開機) (3/3) MT6323 Power On/Off sequence VCORE≈0.7V~1.3V VPORC≈0.7V~1.3V VIO18=1.8V VIO28=2.8V VM12_INT=1.2V VA1=2.5V VA2=2.5V VUSB=3.3V VTCXO=2.8V VMC=3.3V VMCH=3.3V RESET=1.8V Company confidential...
  • Page 9 BB-2 Can not download (無法更新軟件) (1/3) • 1. Please check whether current is normal after boot (確認開機後電流起跳正常) • (記憶體中無代碼時，電池電流約在0.1A左右) • 2. If current in booting process is larger or less than normal, USB port will be unidentified (開機過程中如果電流過大或過小，會造成USB port無法識別) • 3.
  • Page 10 BB-2 Can not download (無法更新軟件) (2/3) • 4. If DL is passed, and META mode is un-entered, check RF transceiver 26MHz and RF chip function (若可以正常DL，但無法進入META mode，檢查RF transceiver 26MHz及RF chip是否正常。) Company confidential...
  • Page 11 BB-2 Can not download (無法更新軟件) (3/3) • 5. Check if com port is correct (確認com port是否正確) Company confidential...
  • Page 12 BB-3 Can not charging (無法充電) (1/2) 1. Check if battery resistance R332 Pin1(BAT_ID) is 10kΩ when • battery is installed (確認電池內阻R332 Pin1 (BAT_ID)， 當接 電池 後阻抗應該約10kΩ.) • 2. Check battery voltage, if 0V reveals open circuit (確認電池電壓 是否為正常，異常為0V (開路)) • 3.
  • Page 13 BB-3 Can not charging (無法充電) (2/2) • 4. Check charging IC and related circuit soldering condition is good (確認充電IC 及周围电路焊接是否 常。) – When USB port has be inserted, VBUS should be at 5V output (VBUS在USB 插入時，是否有5V 右的电压输出。) Company confidential...
  • Page 14 BB-4 SIM Card Identification error (SIM卡無法識別) (1/2) • 1. Check if SIM Card is in normal condition (更換SIM卡，確認卡片是否正常?) • 2. Check if J3200 soldering condition is normal (確認J3200吃錫狀況是否正常?) • 3. Check SIM related signal SRST, VSIM, SIO and SCLK (確認SIM 相關訊號) –...
  • Page 15 BB-4 SIM Card Identification error (SIM卡無法識別) (2/2) SIM1/SIM2的供电电 压各来自PMU的两 组LDO output SIM1/SIM2 output voltage are coming from two LDO output of PMU SIM1和SIM2的 DATA/RST/CLOCK 单独分开使用 DATA/RST/CLOCK of SIM1 and SIM2 are used seperately Company confidential...
  • Page 16 BB-5 Can not display (畫面無法顯示或顯示異常) • 1. Check J904 soldering condition (確認J904是否有異狀[鍚短 or 空焊]?) • 2. Replace LCD (更換LCM) • If failure still exists after LCM replacement (若更換良品後，現象還存在) • 3. Check L1202 L1203 L1204 condition (檢查L1202, L1203, L1204否有異狀?) • 4. Check if LCM voltage (VIO28_PMU及VIO18_PMU) are correct (確認LCM 電壓 (VIO28_PMU及VIO18_PMU)位準是否正確?) •...
  • Page 17 BB-6 sensor function fail (感測器不良) (1/2) • 所有的sensor都是由I2C總線，中斷信號，電源組成.I2C總線上sensor間會相互影響， 所以維修某個 sensor不良時需要同 檢查其他sensor路徑。 • All sensors are consisted by I2C bus, interrupt signal and power. Sensors on I2C bus are affected by each other, therefore related sensors checking is needed when repairing sensor. G-sensor供电电压。该电压等同于...
  • Page 18 BB-6 sensor function fail (感測器不良) (2/2) G-sensor I2C通過上拉電阻連接到CPU，此I2C與touch panel共用， VDD18_PMU異常會造成所有sensor fail。 G-sensor I2C connect to CPU with Pull-up resistor, which share with touch panel, VDD18_PMU error will lead to all sensors failure. Company confidential...
  • Page 19 BB-7 Touch Panel no function (無法觸屏) (1/2) • 1. Check if TP connector is loosen (確認TP Connector 是否鬆脫?) • 2. Replace TP (更換TP) • If failure still exists after TP replacement (若更換後良品後，現象還存在) • 3. Check if J2001 is on failure (確認J2001是否有異狀[鍚短 or 空焊]? ) •...
  • Page 20 BB-7 Touch Panel no function (無法觸屏) (2/2) • TP circuit 復位信號 Reset Signal TP 作電壓 2.8V/1.8V TP Working Voltage 2.8v/1.8v Company confidential...
  • Page 21 BB-8 Vibrator no function (馬達無振動) • 1. Check if motor is in normal condition (Resistance is 30Ω) (確認馬達是否正常 (馬達阻抗約30Ω)) • 2. Check if motor soldering condition (確認馬達是否有異狀[鍚短 or 空焊]?) • 3. Check if D309 is reversed, C331 soldering condition is good (檢查D309是否反 向，C331焊接是否有异常[鍚短...
  • Page 22 BB-9 Camera can not turn on (無法攝像) (1/4) • 1. Check camera module has been well assembled (確認組裝是否到位?) • 2. Replace camera module (更換camera module) • If failure still exists after camera module replaced (若更換後良品後，現象還存在) • 3. Check J902 is in normal condition (確認J902是否有異狀[鍚短 or 空焊]? ) •...
  • Page 23 BB-9 Camera can not turn on (無法攝像) (2/4) • 主camera的4組 作電壓均是由PMU LDO輸出通過給camera • All 4 working voltage of main camera are inputted from PMU LDO Camera 源頭路徑 Company confidential...
  • Page 24 BB-9 Camera can not turn on (無法攝像) (3/4) • 1:無法進入拍攝模式, 為camera無法通過I2C信號 被CPU 常識別造成, 不良主要查供電 /reset/CLK/PWD是否 常 • 1. Camera shooting model is not accessible. The main cause is camera cannot be identified by CPU via I2C, need to check power supply for camera.
  • Page 25 BB-9 Camera can not turn on (無法攝像) (4/4) VREF/HREF: Sensor垂直/水平參考信號 Sensor reference of horizon and vertical MCLK: 來自CPU的主時鐘輸出 Main clock from CPU PCLK: 象數時鐘輸入 Clock input from image-numerology Company confidential...
  • Page 26 BB-10 MIC no function (麥克風無作用) • 1. 確認J1003 Microphone是否正常 (正常Mic阻抗約0.95KΩ) – Check if J1003 Microphone is in normal condition, MIC resistance should be at 0.95KΩ. • 2. 確認MIC 周邊電路是否有異狀[鍚短 or 空焊]? – Check MIC and related circuit soldering condition. MIC1 MIC2 Company confidential...
  • Page 27 BB-11 Speaker no function (喇叭無聲) • 1. 確認MB to SB FPC是否連接ok • Check MB to SB FPC is well connected • 2. 確認Speaker彈腳及阻抗是否正常 (正常阻抗約8Ω) • Check speaker shrapnel and resistance are at normal condition (normal resistance is 8Ω) • 3. 確認Speaker周邊電路是否異常？[鍚短 or 空焊]? •...
  • Page 28 BB-12 Audio function fail (Audio 不良) (1/4) Audio类不良针对不同测试项fail,检查不同的路径. 1:wave play back fail测的是SPK路径. 2:receiver fail 测的是手机听筒路径. 3:headset fail 测的是耳机 右声道路径. 4:phone mic1 to headset fail 测的是手机MIC1路径. 5:phone mic1 to headset fail 测的是手机MIC1路径. 6:headsetmic to headset fail 测的是耳机MIC路径. Check relevant path for different test item failure for Audio error 1:wave play back fail ...
  • Page 29 BB-12 Audio function fail (Audio 不良) (1/4)  Speaker path: PMU給出SPK信號進入Audio PA 進行放大處理 PMU output SPK signal to Audio PA to amplify Audio PA 輸出放 大后的SPK信號 Audio PA output SPK signal after amplifying Company confidential...
  • Page 30 BB-12 Audio function fail (Audio 不良) (2/4)  Receiver path: 聽筒無聲,優先check 0om是否 通 Check 0Com first if receiver is not functional PMU輸出音頻信號 PMU output audio signal  Phone MIC path 為MIC提供偏置電壓 Provide bias voltage for MIC MIC信號輸入到 PMU進行音頻處理 MIC signal input to PMU to process audio Company confidential...
  • Page 31 BB-12 Audio function fail (Audio 不良) (3/4)  耳機 右聲道電路: Earphone L/R channel circuit PMU輸出耳機音頻信號 耳機 右聲道連接 audio jack PMU output earphone audio Earphone L/R channel link to audio jack signal 耳機MIC路徑 Earphone MIC path 耳機掛機鍵偵測信號 Earphone dial- 耳機插入偵測PIN button detection Earphone insert detection pin Company confidential...
  • Page 32 BB-12 Audio function fail (Audio 不良) (4/4)  耳機MIC電路 Earphone MIC Circuit: 為耳機MIC提供偏置電壓 Provide bias votage for earphone MIC 耳機MIC信號通過差分電路進入PMU作音頻處理 Earphone MIC signal output to PMU to be process by differential circuit Company confidential...
  • Page 33 BB-13 SD Card no function (SD Card無作用) • 1. Check SD card is been inserted properly (確認SD CARD有確實卡到位) • 2. Check SD card related circuit are in good condition (確認SD Card周邊電路是 否異常？[鍚短 or 空焊]?) SD card 數據傳輸 SD card 供電端 Data transmission Power supply SD card 控制信號...
  • Page 34 WIFI/BT/GPS WIFI/BT/GPS 功能使用的IC為MTK MT6627 WIFI/BT/GPS IC are MTK MT6627 I/Q Signal Connect to CPU MT6582 獨立的26M TCXO，Output SCLK,DataSignal Clock to MT6627 Separate 26M TCXO, output clock to MT6627 Company confidential...
  • Page 35 WIFI/BT/GPS  MT6627 Power Supply Output to MT6627 From PMU MT6323 Company confidential...
  • Page 36 GSM PA + Switch Logic control table GSM HB/LB Rx Logic control signal WCDMA Band HB/LB TRx GSM Vbat GSM LB Tx input GSM HB Tx input Company confidential...
  • Page 37 GSM RX GSM HB/LB Circuit: 2G LB Rx Balance output to transceiver LB Port 2G HB Rx Balance output to transceiver HB Port Company confidential...
  • Page 38 WCDMA Band1/8 TRx (VV36/38) Rx balance to transceiver TRx connect with ANT Switch Rx balance to transceiver TRx connect with ANT Switch Band 8 Tx Tx from Transceiver Band 1 Tx Company confidential...
  • Page 39 WCDMA Band2/5 TRx (VV37) Rx balance to transceiver TRx connect with ANT Switch Rx balance to transceiver TRx connect with ANT Switch Band 5 Tx Tx from Transceiver Band 2 Tx Company confidential...
  • Page 40 RF introduction: MT6166 Function Block Company confidential...
  • Page 41 RF introduction: MT6166 Pin assignment Company confidential...
  • Page 42 RF introduction: Antenna Circuit • Antenna Circuit RF天線主要包含了 2G/3G/WIFI/GPS, 其匹配電路分別描述如 Main ANT RF Paths RF antenna consists 2G/3G/WIFI/GPS, Description as right diagram WIFI ANT RF Paths Wifi /BT path GPS path Company confidential...
  • Page 43 RF introduction:2G/3G Main Antenna Position ANT Matching MB RF Switch Connect to Sub by Coaxial Cable Company confidential...
  • Page 44 RF introduction: WIFI Antenna Position WiFi/BT/GPS WiFi/BT/GPS Antenna Antenna Clips Matching Company confidential...
  • Page 45 RF common issue RF-1:Network function error RF-2:GSM problem RF-3:WCDMA problem RF-4:GSM/WCDMA Rx error RF-5:WIFI problem Company confidential...
  • Page 46 RF-1:Network function error • 若2G/3G 網路功能異常,請檢查螢幕天線格數,SIM card是否裝好? Coaxial cable和是否組好? • If 2G/3G network is on failure, check reception level on screen, SIM card inserted properly and Coaxial cable connected well. Company confidential...
  • Page 47 RF-2:GSM Trouble shooting (1/3) • Check GSM transmission path (檢查GSM發射路徑) Tx I/Q Signal Company confidential...
  • Page 48 RF-2:GSM Trouble shooting (2/3) • GSM發射路徑 GSM transmission path – 由於2G PA和ASM整合在U1302,檢查發射時對應邏輯控制電壓是否正確 – Due to 2G PA and ASM assembly in U1302, check logical control voltage is correct when transmission testing – 使用示波器量測 圖所標腳位的電壓是否符合右 列表 – Use oscilloscope test below pins voltage if they match the right bottom table Company confidential...
  • Page 49 RF-2:GSM Trouble shooting (3/3) • GSM發射路徑 GSM transmission path – 檢查發射路徑的功率 – check power of transmission path – 使用spectrum probe量測 列標駐點,測量其功率 Use spectrum probe to measure below points’ power – High band GSM signal Low band GSM signal Company confidential...
  • Page 50 RF-3:WCDMA Trouble shooting (1/5) • WCDMA發射路徑 WCDMA transmission path – 確認IQ路徑 – Check IQ path – 使用示波器量測 圖所標之腳位,檢視其波形 – Use oscilloscope to check below points, check waveform. Company confidential...
  • Page 51 RF-3:WCDMA Trouble shooting (2/5) • WCDMA發射路徑 WCDMA transmission path – 確認發射路徑 – Check signal transmission path – 使用频谱仪量測 圖所標之腳位,檢視其Power – Use oscilloscope to test below point and power Company confidential...
  • Page 52 RF-3:WCDMA Trouble shooting (3/5) • WCDMA發射路徑 WCDMA transmission path Transceiver-3G PA, PA-Duplexer From MT6166 From MT6166 WCDMA BAND 1/2 signal WCDMA BAND 1/2 signal Company confidential...
  • Page 53 RF-3:WCDMA Trouble shooting (4/5) WCDMA發射路徑 WCDMA transmission path – 檢查ASM 邏輯控制電壓 – Check ASM logical control voltage – 使用示波器量測 圖所標腳位的電壓,是否符合右 列表 – Use oscilloscope test below pins voltage if they match the right bottom table Company confidential...
  • Page 54 RF-3:WCDMA Trouble shooting (5/5) • 發射路徑 ASM-RF Con (GSM + WCDMA) • Transmission Path ASM-RF Con (GSM + WCDMA) GSM PA+ASM Company confidential...
  • Page 55 RF-4:GSM/WCDMA Trouble shooting • 接收路徑 Receiving Path – 檢查 Antenna switch Module邏輯控制電壓 – Check Antenna switch module logical control voltage – 使用示波器量測 圖所標腳位的電壓是否符合右 列表 – Use oscilloscope test below pins voltage if they match the right bottom table Company confidential...
  • Page 56 WIFI/BT/GPS WIFI/BT/GPS IC: MTK MT6627 BT/WIFI: 1. Check whether the antenna of BT\WIFI damaged 2. Check whether BT\WIFI R1503 has output frequency of 26M co _ clock design 3. Check BT\WIFI TRX path Company confidential...
  • Page 57 WIFI/BT/GPS BT/WIFI TRX path ： Co_clock design： MT6166 U1303 MT6627 U1504 MT6627 U1504 Company confidential...
  • Page 58 WIFI/BT/GPS GPS RX path ： 1. Check whether the antenna of GPS damaged 2. Check whether the working voltage is normal Vcc:2.8V;GPS_LNA_EN:1.8V 3. Check whether the GPS signal has been enlarged Company confidential...
  • Page 59 WIFI/BT/GPS GPS RX path U1506 MT6627 U1504 Company confidential...
  • Page 60 Thank You！ Company confidential...