Advertisement
Quick Links
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly
maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS,
WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY, AND WILL INVALIDATE THE WARRANTY. PLEASE
KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1.
SAFETY INSTRUCTIONS
1.1
GENERAL SAFETY
WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations
are adhered to when using this product.
WARNING! Use caution when handling and assembling the metal components. The metal may
have sharp edges or corners, the use of protective gloves is recommended.
This mounting frame can only be attached to the AP165WB Work Bench (sold separately),
failure to do so may cause personal injury or damage to the product.
Locate work bench mounting frame assembly in a suitable working area.
Secure the assembly to wall.
Keep the work area clean, uncluttered and ensure there is adequate lighting.
Keep the mounting frame clean and tidy in accordance with good workshop practice.
Keep children and unauthorised persons away from the working area.
Only hang a maximum of two AP02WC cabinets (sold separately) on the frame, the use of
unauthorised components being hung on the frame may cause the assembly to become
unstable and could result in personal injury or damage to the product.
A maximum of four APSPB peg board panels (2 per pack sold separately) can be fitted to the unit.
DO NOT exceed the maximum weight for each peg board panel of 20kg (45lb).
DO NOT use the mounting frame for any purpose other than that for which it is designed.
DO NOT climb on the mounting frame.
DO NOT use in damp work areas.
WARNING! The warnings, cautions and instructions referred to in this instruction manual cannot
cover all possible conditions and situations that may occur. It must be understood that common
sense and caution are factors which cannot be built into this product, but must be applied by the
operator.
2.
INTRODUCTION
Main support structure for the professional garage storage system or an individual storage panel. Must be assembled to the AP165WB Work Bench,
AP02WC Cabinets and APSPB peg boards can then be easily hung or fixed to the frame. Manufactured from tough steel with a graphite powder coat
finish for corrosion resistance.
Overall Size (W x D x H):
3.
ASSEMBLY
3.1
Attach the two (A) posts and post (B) to the work bench as
shown in Fig.2. Tighten finger tight only at this stage.
3.2
Attach crossbeam (C) to the uprights as shown in Fig.3,
finger tighten.
Note: Ensure the crossbeam has the two large holes for power
cables.
3.3
Attach crossbeam (D) to the uprights as shown in Fig 4,
ensuring that the two small holes are uppermost and finger
tighten.
3.4
Attach crossbeams (E) and (F) as shown in Fig.5 and finger
tighten.
Note: Crossbeam (F) has holes for the wall securing bracket (G).
3.5
Square the unit and fully tighten all bolts.
3.6
Attach wall securing bracket (G) to crossbeam (F) see
Fig.6, both (G) and (F) have multiple holes to enable the
bracket to allow adjustment with a wall stud and to be flush
with the wall.
3.7
With the workbench and mounting frame located in the
desired position, align the bracket with a wall stud and drill
a 3/16" pilot hole.
3.8
Secure the workbench frame assembly to the wall with
bolt (K).
1648 x 40 x 2340mm
INSTRUCTIONS FOR:
MOUNTING FRAME
FOR GARAGE STORAGE SYSTEM
APMF
MODEL No:
Fig.1
APMF
Issue No: 1 - 13/10/08
Advertisement
Related Manuals for Sealey APMF
Summary of Contents for Sealey APMF
- Page 1 APMF MODEL No: Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS &...
- Page 2 Parts support is available for this product. To obtain a parts list and diagram please log on to www.sealey.co.uk, email sales@sealey.co.uk or phone 01284 757500 NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.