Advertisement
Quick Links
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
Wear eye
instructions
protection
1. SAFETY
Only use on firm, level, unobstructed surfaces which are capable of supporting the stand and drill.
9
Ensure stand is fixed to surface capable of supporting stand, drill and work piece.
9
Replace or repair damaged parts. Use only recommended parts. Unauthorised parts may be dangerous and will invalidate the
9
warranty.
WARNING! Failure to comply with these instructions may result in damage to the stand or other property and/or personal injury.
‰
WARNING! The warnings, cautions and instructions discussed in this instruction manual cannot cover all possible conditions and
‰
situations that may occur. It must be understood that common sense and caution are factors which cannot be built into this product,
but must be applied by the operator
2. INTRODUCTION
The lightweight stand is made of aluminium, can tilt to 45° and features a combined base plate for vacuum or anchor fitting, together with
a practical handle and wheels making it easy and comfortable to transport or carry. Ideal for use with Model No's DCD110V and DCD230V
Diamond Core Drills.
3. SPECIFICATION
Maximum Drill Bit Diameter: . ................................... Ø200mm
Travel Length: ............................................................ 600mm
4. OPERATION
4.1.
ATTACHING DRILL TO STAND REF. FIG 1
4.1.1.
The drill is attached to the stand using the drill clamp (fig.1)
4.1.2.
Remove one half of the drill clamp by means of the screws, slot the drill into place and replace the clamp.
4.1.3.
Secure the clamp by using the two locking handles.
4.2.
SECURING STAND TO THE GROUND
4.2.1.
To bolt the stand to the ground, drill a hole for a securing bolt a suitable distance away from your intended drilling area.
Note:
You do have some adjustment on the drill base but plan before you drill.
4.2.2.
The base can be levelled using the 4 levelling bolts. Adjust these before securing the anchor bolt.
4.3.
SETTING THE ANGLE
4.3.1.
Loosen the angle adjustment bolt and the brace locking handle, slide up or down until you get the desired angle.
fig.1
© Jack Sealey Limited
DIAMOND CORE DRILLS STAND
MODEL NO:
Wear protective
Wear safety
gloves
footwear
Original Language Version
DCDST
Wear protective
Wear ear
clothing
protection
Wear a mask
DCDST Issue 2 (2) 08/07/2020
Advertisement
Related Manuals for Sealey DCDST
Summary of Contents for Sealey DCDST
- Page 1 DCDST MODEL NO: Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
- Page 2 Make sure the machine is mounted in the rig Drill Holes correctly. Clean the machine thoroughly and reassemble the drill and check for run-out again. ENVIRONMENT PROTECTION Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations. Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice. Important: No Liability is accepted for incorrect use of this product. Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim. Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR 01284 757500 01284 703534 sales@sealey.co.uk www.sealey.co.uk DCDST Issue 2 (2) 08/07/2020 Original Language Version © Jack Sealey Limited...