Advertisement
Quick Links
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
Wear eye
instructions
protection
1. SAFETY
WARNING! Ensure Health and Safety, local authority and general workshop practice regulations are adhered to when using tools.
‰
DO NOT use tools if damaged.
8
DO NOT attempt to start engine or move vehicle whilst tools are fitted and work is in progress.
8
Maintain tools in good and clean condition for best and safest performance.
9
Wear approved eye protection. A full range of personal safety equipment is available from your Sealey stockist.
9
Wear suitable clothing to avoid snagging. DO NOT wear jewellery and tie back long hair.
9
Ensure any disconnected fuel pipes are plugged to avoid spillage.
9
Account for all tools and parts being used, DO NOT leave them in or near the engine. Return all parts to the case and store this in a
9
safe, dry, childproof location.
IMPORTANT: These instructions are provided as a guide only. Always refer to the vehicle manufacturer's service instructions, or a
proprietary manual, to establish the current procedure and data.
WARNING! The warnings referred to in this guide cannot cover all possible conditions and situations that may occur. It must be
‰
understood that common sense and caution are factors which cannot be built into this product, but must be applied by the operator.
2. INTRODUCTION
For removing the heater element that can break off during glow plug removal. Saves time not having to remove the cylinder head. Works by
drilling/tapping a thread into the broken element so the supplied glow plug adaptors can be used to extract. Supplied with seven drilling/tapping
guides and five glow plug extraction adaptors with either a M8 or M10 thread.
3. CONTENTS
fig.1
© Jack Sealey Limited
8 & 10MM GLOW PLUG HEATER ELEMENT
REMOVAL SET
VS315
MODEL NO:
KEY:
1 . . . . . . . Drilling Guides: M8 x 1, M10 x 1, M10 x 1.25mm
2 . . . . . . . . . . . . . . Tapping Guides: M8 x 1, M10 x 1.25mm
3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Drills: Ø 2.5, 3.3mm
4 . . . . . . . . . . . . . . . . . . . . . . . Taps: M3 x 0.5, M4 x 0.7mm
5 . . . Extraction Adaptors: M8 x 1, M10 x 1, M10 x 1.25mm
6 . . . . . . . . . . . . . . Threaded Rods: M3 x 0.5, M4 x 0.7mm
7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Extractor Nuts
Original Language Version
VS315 Issue 2 (4) 21/05/20
Advertisement
Related Manuals for Sealey VS315
Summary of Contents for Sealey VS315
- Page 1 VS315 MODEL NO: Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
- Page 2 Select the appropriate tap and cut a thread into the broken glow plug element ensuring the tap is turned back frequently to clear swarf away from the cutter. (fig.4). Ensure a good quality cutting fluid such as Sealey SCSCF400 is used when cutting the thread.
- Page 3 Examine the glow plug element and the aperture to ensure that no debris is in the glow plug port before fitting the replacement glow plug. Parts support is available for this product. Please email sales@sealey.co.uk or telephone 01284 757500 ENVIRONMENT PROTECTION Recycle unwanted materials instead of disposing of them as waste.