Related Manuals for Toro TimeCutter Z 79214
Summary of Contents for Toro TimeCutter Z 79214
- Page 1 Form No. 3329-278 Rev B 38I and 42I Twin Bagger TimeCutter Z Attachment Model No. 79214—Serial No. 230000001 and Up Model No. 79215—Serial No. 230000001 and Up Operator’s Manual Original Instructions (EN)
-
Page 2: Table Of Contents
Whenever you need service, genuine Toro parts, or additional information, contact an Authorized Service Dealer or Toro Customer Service and have the model and serial numbers of your product ready. Figure 1 illustrates the location of the model and serial numbers on the product. -
Page 3: Safety
Safety Safety and Instruction Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. 93-7320 1. Crushing hazard of hand—do not remove the whole bagger from the machine; open the bagger top and then remove the bag(s) from the bagger. -
Page 4: Setup
Setup Note: Determine the left and right sides of the machine from the normal operating position. Loose Parts DESCRIPTION QTY. Weight Bolt, 3/8 x 2-1/4 inch Installing the front weight Locknut, 3/8 inch Washer, 3/8 inch Bagger Quick Attach Bracket Bolt, 3/8 x 1 inch Installing the quick attach bracket Locknut, 3/8 inch... -
Page 5: Installing The Quick Attach Bracket
2. Install the front weight to the bottom footrest frame with 2 bolts (3/8 x 2–1/4 inch), 4 washers (3/8 inch) and 2 nuts (3/8 inch) (Figure 3). Note: Make sure the weight is installed as shown in Figure 3. 3. -
Page 6: Installing The Bagger Assembly
Installing the Bagger Assembly 2. Install the bags by sliding the bag frame hooks onto the retaining brackets (Fig. 7). 1. Carefully lift the bagger top and slide it onto the quick attach bracket (Fig. 6). The bagger top is easier to install if two people work together. -
Page 7: Installing The Blades For Model 79214 Only (42 Inch Mower)
5. Repeat steps 1 through 4 for the opposite blade. m–6619 Figure 9 m–6430 1. Grass deflector 3. Nut Figure 11 2. Pivot rod 1. Sail area of blade 4. Blade bolt 2. Blade 5. Blade stiffener 4. Insert the new pivot rod into the short stand-off on the 3. -
Page 8: Installing The Decal On International Models Only
Removing the Bagger Warning An uncovered discharge opening could allow the lawn mower to throw objects in the operator’s or bystander’s direction and result in serious injury. Also, contact with the blade could occur. Never operate the lawn mower unless you install a cover plate, a mulch plate, or a grass chute and catcher. -
Page 9: Operation
Important The grass deflector must be spring loaded in Warning the down position. Lift the deflector up to test that it snaps to the full down position. If you remove the spring-loaded bagger top when it is closed (in the down position), the top may suddenly fly open and you or someone else may be bruised, pinched, or injured in another way. -
Page 10: Clearing Obstructions From The Bagger
Cutting Technique 4. Install the bags by sliding the bag frame hooks onto the retaining brackets (Fig. 7). For best lawn appearance, be sure to slightly overlap the 5. Lower the bagger top onto the bags. Then push down mower into the previously cut area. This helps reduce the on both bag retainer handles until they lock on the bag load on the engine and reduces the chance of plugging the frame (Fig. -
Page 11: Maintenance
bagging system, mow the grass at a high height of cut, then Caution lower the mower to your normal cutting height and repeat the bagging process. As the bagger fills, extra weight is added to the back of the machine. If you stop and start Bagging Wet Grass suddenly on hills, you may lose steering control or Always try to cut grass when it is dry because your lawn... -
Page 12: Inspecting The Bagger Attachment
Inspecting the Bagger Storing the Bagger Attachment Attachment 1. Clean the bagger attachment; refer to Cleaning the Bagger Attachment, page 12. Inspect the bagger attachment after the first 10 hours of operation, and monthly thereafter. 2. Inspect the bagger attachment for damage; refer to Inspecting the Bagger Attachment, page 12. -
Page 16: The Toro Total Coverage Guarantee
If for any reason you are dissatisfied with your Distributor’s service or have difficulty obtaining guarantee information, contact the Toro importer. If all other remedies fail, you may contact us at Toro Warranty Company.