Table of Contents
Advertisement
Quick Links
TX Platform
Gasoline-Powered TX Compact Utility Loader
Model No. 22475—Serial No. 270000001 and Up
Model No. 22476—Serial No. 270000001 and Up
Safety
General Operation
•
Do not modify the platform or use it on
non–approved machines.
•
Ensure that the platform is properly attached to the
machine and is in good working order prior to use.
•
Allow only the machine operator on the platform.
•
Do not allow use of the platform by untrained
operators.
•
Use appropriate personal protective apparatus for
eyes, feet, hands, and head.
•
Look behind and down before backing up to be
sure of a clear path.
•
Use extra care when operating in reverse.
•
Dismount and latch the platform in the transport
position when loading and unloading the machine.
•
Do not place your feet under the platform.
•
Slow down before turning. Sharp turns on any
terrain may cause loss of control.
•
Do not step off of the platform with the load raised.
•
Keep your hands, feet, hair, and loose clothing
away from any moving parts.
•
Do not try to stabilize the traction unit by putting
your foot on the ground.
•
Do not operate platform on rough and uneven
terrain.
•
Ensure that you operate the platform in areas
where there are no obstacles in close proximity
to the operator. Failure to maintain adequate
distance from trees, walls, and other barriers may
result in injury as the platform backs up or turns
during operation if the operator is not attentive to
the surroundings. Only operate the unit in areas
where there is sufficient clearance for the operator
to safely maneuver the platform.
•
Ensure that the area is clear of other people before
operating the traction unit with the platform. Stop
the traction unit if anyone enters the area.
•
Do not exceed the rated operating capacity, as
the traction unit with the platform may become
unstable which may result in loss of control.
© 2020—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
Service
•
•
•
•
•
Register at www.Toro.com.
Installation Instructions
Stop the engine before performing any service,
repairs, maintenance, or adjustments
Keep nuts and bolts tight. Keep equipment clean
and in good condition.
Never tamper with safety devices. Check safety
systems for proper operation before each use.
Stop and inspect the equipment if you strike
an object. Make any necessary repairs before
restarting.
Use only genuine replacement parts to ensure that
original standards are maintained.
Original Instructions (EN)
All Rights Reserved *3439-615* A
Printed in the USA
Form No. 3439-615 Rev A
Advertisement
Table of Contents
Related Manuals for Toro TX Platform
Summary of Contents for Toro TX Platform
- Page 1 • Do not exceed the rated operating capacity, as the traction unit with the platform may become unstable which may result in loss of control. © 2020—The Toro® Company Register at www.Toro.com. Original Instructions (EN) All Rights Reserved *3439-615* A...
-
Page 2: Safety And Instructional Decals
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. decal94-3353 94-3353 1. Crushing hazard of hand—keep hands away. decal58-6520 58-6520 1. -
Page 3: Preparing The Traction Unit
Preparing the Traction Unit Installing the Platform No Parts Required Parts needed for this procedure: Platform assembly Procedure Bolt (1/2 x 1-1/2 inches) Stop the engine, lower the loader arms, set the Flange-head nut (1/2 inch) parking brake, and remove the key. Wash all dirt and debris from the traction unit. - Page 4 g004400 Figure 3 Left side not shown. 1. Bolt (2 on each side) 2. Flange-head nut (2 on each side) 3. Bolt (1/2 x 1-1/2 inches) Note: Figure 3 shows a TX 500 series traction Install the mounting brackets (Figure 5) onto the unit.
- Page 5 g004402 Figure 5 1. Flange-head nut (1/2 inch) 2. Platform Torque the flange-nuts to 91 to 113 N∙m (67 to 83 ft-lb). Align the platform so that it is centered on the machine (Figure 4), then torque the 4 bolts and nuts securing the platform assembly to the mounting brackets to 91 to 113 N∙m (67 to 83 ft-lb).
- Page 6 Installing the Installing the Decal Counterweight (TX 500 No Parts Required Series Traction Units Only) Procedure Parts needed for this procedure: Clean the area behind the traction control (Figure 7) so that there is not dirt or grease on it. Counterweight Bolt (1/2 x 1-1/4 inches) Washer...
-
Page 7: Installing The Handle
Installing the Handle Parts needed for this procedure: Handle Flange-head bolts (5/16 x 3/4 inch) Procedure Remove the rear access cover; refer to you traction unit Operator’s Manual for instructions. Locate and drill 2 holes—9.5 mm (3/8 inch g004404 diameter) on the control panel below the loader Figure 9 arm lever, as shown in Figure... -
Page 8: Operation
Operation WARNING If you step off of the platform with a heavy load raised, the machine could tip forward quickly, injuring your and/or pinning bystanders. Do not step off of the platform with the load raised. WARNING Unless you are carrying heavy loads or attachments, the platform with an operator will make the rear of the machine the heavy g004405... -
Page 9: Maintenance
8 operating hours. Replace it if it is damaged. Grease all pivot joints every 8 operating hours and Important: Use only a genuine Toro replacement immediately after every washing. shear bolt and nut. Other bolts will not function correctly and may lead to an unsafe condition. - Page 10 Notes:...
- Page 11 Notes:...
- Page 12 Countries Other than the United States or Canada Customers who have purchased Toro products exported from the United States or Canada should contact their Toro Distributor (Dealer) to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisfied with your Distributor’s service or have difficulty obtaining guarantee information, contact the Toro importer.