Page 1
FILE NO. 810-200310X SERVICE MANUAL COMPACT COMPACT DIGITAL VIDEO DIGITAL AUDIO V I D E O DVD HOME THEATER SYSTEM SD-43HKSB SD-43HKSE A pril. 2003...
Page 4
CONTENTS 1. Alignment and Adjustments 2. Exploded Views and Parts List 3. Diassembly and Reassembly 4. Electrical Parts List 5. Block Diagrams 6. PCB Diagrams 7. Wiring Diagram 8. Schematic Diagrams 9. IC block Diagrams 10. Troubleshooting...
Page 5
Output SSG FREQ. 450 kHz Output(Fig1-4) AM IF Frequency 522 kHz AM ANT OUTPUT Adjustment AM IF point Speaker Terminal AM SSG 450KHZ Maximum output (Figure 1-3) OUTPUT INPUT VTVM Oscilloscope Figure1-3 AM I.F Adjustment Fig 1-4 OSC Voltage TOSHIBA...
Page 6
1.0V±0.1V at the low. 7.3MHz Check for 8.5V±1.0V at the high. 3.5MHz 3.5MHz SW1 ANT Maximum out Fig 1-3 9.5MHz SW2 OSC Adjust for 1.5V±0.1V at the low. 26.1MHz Check for 8.0V±1.0V at the high. 10MHz 10MHz SW2 ANT Maximum out TOSHIBA...
Page 7
2.Exploded Views and Parts List 2-1 Total Exploded View TOSHIBA...
Page 12
1. Turn on the power and open the disc tray. 2. Slightly twist the assembly door in the direction of A and lift it in the direction of B to remove it. 3. Close the assembly door. TRAY ASS’Y DOOR TOSHIBA...
Page 13
1. Take out the 5 screws (B) and the 2 screws (C). 2. Disconnect the flexible cable and then remove the cabinet front. FLEXIBLE CABLE CABINET FRONT 3-1-4. CABINET REAR 1. Take out the 15 screws (G), unplug the connector, and then remove the cabinet rear. CABINET REAR CONNECTOR TOSHIBA...
Page 14
1. Take out the screw (B) and disconnect the flexible cable. 2. Unplug the 3 connectors (CONNECTOR(1)) and then remove the DSP PCB-1. 3. Unplug the 2 connectors (CONNECTOR(2)) and then remove the DSP PCB-2. CONNECTOR(2) FLEXIBLE CABLE DSP PCB-2 DSP PCB-1 CONNECTOR(1) TOSHIBA...
Page 15
3-2-3. AUX PCB 1. Unplug the connector and then remove the AUX PCB. AUX PCB CONNECTOR 3-2-4. POWER PCB 1. Take out the 4 screws (H). 2. Unplug the 2 connectors and then remove the POWER PCB. POWER PCB CONNECTOR TOSHIBA...
Page 16
AMP PCB CONNECTOR CONNECTOR 3-2-6. FRONT PCB-1, FRONT PCB-2 1. Remove the KNOB VOLUME and take out the 10 screws (D). 2. Unplug the connector and remove the FRONT PCB-1 and FRONT PCB-2. FRONT PCB-1 FRONT PCB-2 CONNECTOR KNOB-VOLUME TOSHIBA...
*S.N.A. : Service Not Available 4. Electrical Parts List TOSHIBA TOSHIBA SAMSUNG SAMSUNG LOCATION Description;Specification REMARK LOCATION Description;Specification REMARK PART NO. CODE NO. PART NO. CODE NO. AG000525 AH26-00241C TRANS POWER;-,HT-DM150N,-,0,230V,##22/## AR44 AG000120 2007-000074 R-CHIP;100ohm,5%,1/10W,TP,1608 AR51 AG000120 2007-000074 R-CHIP;100ohm,5%,1/10W,TP,1608 AG000528 AH39-00257F POWER CORD;CP2,250V,2.5A,1830MM...
Page 45
3. Protection(When High Voltage at Protection port) 3-1 In this case “LOW” for, Base port of Q 12(R2003 TR)at MAIN PCB TOSHIBA 10-3...
Page 46
3-2 In this case “LOW” for Base of Q 13(A733)at Main PCB 3-3 Check the Connector Wire Ass’y Connection of each PCB ;DVD MECHA-Main PCB (8P, PW4) ;POWER TRANS-Main PCB (CW3) ;POWER TRANS-Main PCB (PW2) ;POWER TRANS-Main PCB (PW1) 10-4 TOSHIBA...
Page 47
10-2 DVD Servo Parts V : 1V/div V : 1V/div V : 1V/div H : 5ns/div H : 5ns/div H : 5ns/div Fig. 1-2 Fig. 1-3 Fig. 1-4 TOSHIBA 10-5...
Page 56
3.Audio operation Check Audio Digital signal Check Audio out signal at pin 23~28pin of AIC1 at pin 33,36,37 of U13 Audio out Check Main AMP parts Audio Digital Signal 10-14 TOSHIBA...
Page 57
1-1, SHIBAURA 1- CHOME, MINATO - KU, TOKYO 105 - 8001, JAPAN...