Table of Contents
Advertisement
Quick Links
Microprocessor and Memory
Technologies Group
Errata and Added Information to
MC68360 Quad Integrated Communication
Controller User's Manual Rev 1
January 8, 1998
This document describes the latest information and changes to the first revision of the
MC68360 user's manual.
Section 2 – Signal Descriptions
1. QUICC Functional Signal Groups.
On page 2-2, Figure 2-1, the signal names in the left column had a typo. The corrections for
the typo are in the right column.
As seen on page 2-2
A31-A27/WE3-WE0
SDACK2/L1TSYNCB/CTS3/PC8
L1RSYNB/CD3/PC9
SDACK1/L1TSYNCA/CTS4/PC10
L1RSYNCA/CD4/PC11
2. Error on TRIS
On page 2-4, Table 2-1, the function description of TRIS stated that it is sampled during
system reset. This is not true. The TRIS signal is always sampled except during reset.
3. Missing Note.
On page 2-8, section 2.1.7.2 the following note should be added:
User should note that the pin AVEC/IACK5 is always an open
drain output.
This document contains information on a product under development. Motorola reserves the right to change or discontinue this product without notice.
© MOTOROLA, 1995
Freescale Semiconductor, Inc.
SEMICONDUCTOR PRODUCT INFORMATION
For More Information On This Product,
Go to: www.freescale.com
Correction
A31-A27/WE0-WE3
SDACK2/L1TSYNCB/CTS3/PC8
L1RSYNB/CD3/PC9
SDACK1/L1TSYNCA/CTS4/PC10
L1RSYNCA/CD4/PC11
NOTE
Order this document by
MC68360UM/AD
MC68360
Advertisement
Table of Contents
Related Manuals for Motorola MC68360
Summary of Contents for Motorola MC68360
-
Page 1: Section 2 - Signal Descriptions
User should note that the pin AVEC/IACK5 is always an open drain output. This document contains information on a product under development. Motorola reserves the right to change or discontinue this product without notice. SEMICONDUCTOR PRODUCT INFORMATION © MOTOROLA, 1995 For More Information On This Product, Go to: www.freescale.com... -
Page 2: Section 3 - Memory Map
“The equations of the byte write enables for 32-bit port (16BM = 1) are as follows” “The equations of the byte write enables for 16-bit port (B16M = 0) are as follows:” MC68360 USER’S MANUAL ERRATA MOTOROLA For More Information On This Product,... - Page 3 If the problem occurs, the only solution is powering the device down and reapplying power (i.e. another power-on reset). Hardware reset (RESETH) will not solve the problem. MOTOROLA MC68360 USER’S MANUAL ERRATA For More Information On This Product, Go to: www.freescale.com...
-
Page 4: Section 6 - System Integration Module
The internal frequency of the 68360 and the output of the CLKO pins is dependent upon both the quality of the crystal circuit and the multiplication factor (MF) used in the PLLCR register. Please MC68360 USER’S MANUAL ERRATA MOTOROLA For More Information On This Product,... - Page 5 This is not correct and the sentence should be removed. 3. Missing Text. On page 6-30, section 6.9.3.1, the note “SUPERVISOR ONLY” should appear below the MCR register. MOTOROLA MC68360 USER’S MANUAL ERRATA For More Information On This Product, Go to: www.freescale.com...
- Page 6 On page 6-57, section 6.11.7, the following note should be added after the first paragraph. NOTE The MC68EC040 and MC68040 type master is not supported when the QUICC is configured to a master mode. MC68360 USER’S MANUAL ERRATA MOTOROLA For More Information On This Product, Go to: www.freescale.com...
- Page 7 DRAM bank (PGME = 1), and when a zero wait state DRAM is implemented by setting TCYC to be zero. If this is not done the DRAM may latch invalid data during writes. MOTOROLA MC68360 USER’S MANUAL ERRATA For More Information On This Product, Go to: www.freescale.com...
- Page 8 18. Missing NOTE. On page 6-74, bits 3 and 2 of the option register should have an asterisks. Also on the bottom of the page the following note should be added. MC68360 USER’S MANUAL ERRATA MOTOROLA For More Information On This Product,...
- Page 9 The correct section number is 7.6.2.5. 5. Wrong table reference. On page 7-35, first sentence in section 7.6.4.2.1 reference, table 7-2. This should be table 7-3. MOTOROLA MC68360 USER’S MANUAL ERRATA For More Information On This Product, Go to: www.freescale.com...
- Page 10 On page 7-72, section 7.8.4.5, the bit order of SSEL1-SSEL4 is not represented correctly. The correct representation is as follows: Bit 13 -> SSEL4 Bit 12 -> SSEL3 Bit 11 -> SSEL2 Bit 10 -> SSEL1 MC68360 USER’S MANUAL ERRATA MOTOROLA For More Information On This Product, Go to: www.freescale.com...
- Page 11 “If the DPLL is not used …” with the following: “To bypass the DPLL, choose the 1x value, except in asynchronous UART mode where 8x,16x, or 32x still must be used.” MOTOROLA MC68360 USER’S MANUAL ERRATA For More Information On This Product, Go to: www.freescale.com...
- Page 12 0 = 10 bits 1 = 9 bits Bit 1 – BCM (HDLC BUS Collision Sense Mode) This bit determines the sample point of collision detection. MC68360 USER’S MANUAL ERRATA MOTOROLA For More Information On This Product, Go to: www.freescale.com...
- Page 13 This is not correct DMA_cnt does not need to be initialized by the user and should have been in plain font. MOTOROLA MC68360 USER’S MANUAL ERRATA For More Information On This Product, Go to: www.freescale.com...
- Page 14 If a buffer is ended with the L-bit set, then the next buffer can appear in any time slot associated with this channel. MC68360 USER’S MANUAL ERRATA MOTOROLA For More Information On This Product, Go to: www.freescale.com...
-
Page 15: Section 9 - Applications
On page 9-2, Figure 9-1, the MODCK0-1 pins are shown to be connected to Vcc. The correct figure has MODCK0 connected to ground and MODCK1 connected to Vcc. MOTOROLA MC68360 USER’S MANUAL ERRATA For More Information On This Product, Go to: www.freescale.com... - Page 16 QUICC even though there are not applicable to the current bus size. 5. MC68040 Companion Mode Bus Cycle Note. On page 9-31, section 9.4, add the following note: NOTE MC68360 USER’S MANUAL ERRATA MOTOROLA For More Information On This Product, Go to: www.freescale.com...
-
Page 17: Section 10 - Electrical Characteristics
On Page 10-1, the following note should be added to the maximum ratings figure: 3. The supply voltage V must start and restart from 0.0 V; otherwise, the 360 will not come out of reset properly. MOTOROLA MC68360 USER’S MANUAL ERRATA For More Information On This Product, Go to: www.freescale.com... -
Page 18: Dc Electrical Specifications
15 3,10,12 AS, DS, CSx, OE, WE Width Negated t SN — 26.25 — 17A 13 CSx Negated to R/W High t CNRN — 22.5 — CLKO1 High to R/W High t CHRH MC68360 USER’S MANUAL ERRATA MOTOROLA For More Information On This Product, Go to: www.freescale.com... - Page 19 Non page mode @WBTQ=1 9. Typo on R/W Low to CASx Asserted. On page 10-28, Table 10.10 specification 115 was printed incorrectly. The correct spec is as follows: MOTOROLA MC68360 USER’S MANUAL ERRATA For More Information On This Product, Go to: www.freescale.com...
- Page 20 User should note that the negation timing of bus request from a slave QUICC pin may not meet the required input specification for the QUICC in master mode. Because of this the MC68360 USER’S MANUAL ERRATA MOTOROLA For More Information On This Product,...
- Page 21 On page 10-45 and page 10-47 the specification number for R/W to AS assertion should be 214 not 164 18. Typo on External MC68030/MC68360 DRAM Asynchronous Cycle Timing Diagram. On page 10-47, Figure 10-35, the specification for AMUX signal negation should be 119.
- Page 22 On page 10-57 the figure title should be replaced with the following Figure 10-44(a). MC68040/EC040 SRAM Read Cycles (TSS40=0, CSNT40=1) The following figure should be added after figure 10-44(a) MC68360 USER’S MANUAL ERRATA MOTOROLA For More Information On This Product,...
- Page 23 Figure 10-45(a) MC68040/MC68EC040 SRAM Write cycle (TSS40=1, CSNT40=1) NOTE OE and WE signals are not supported when TSS40 is set to 1. The following figure should be added below figure 10-45(a) MOTOROLA MC68360 USER’S MANUAL ERRATA For More Information On This Product, Go to: www.freescale.com...
- Page 24 On page 10-62, replace the entries for specification numbers 1 and 2 with the following: 3.3 V or 5.0 V 5.0V Num. Characteristic Unit 25.0 MHz 33.34MHz CLKO1 Low to DACK, DONE Asserted CLKO1 Low to DACK, DONE Negated MC68360 USER’S MANUAL ERRATA MOTOROLA For More Information On This Product, Go to: www.freescale.com...
-
Page 25: Section 11 - Ordering Information And Mechanical Data
Dual port ram to ZERO after reset. This will prevent any unwanted bit to be set in the dual port ram that may cause undesired result. MOTOROLA MC68360 USER’S MANUAL ERRATA For More Information On This Product, Go to: www.freescale.com... - Page 26 0.0ns and less than 2.0ns (for rise time of 4ns), otherwise, this skew is not guaranteed. However, for MF<10 and input frequencies greater than 10MHz, this skew is between -3.0ns and +4.0ns. MC68360 USER’S MANUAL ERRATA MOTOROLA For More Information On This Product,...
- Page 27 (a). EXTAL and QUICC internal clock phases will not be synchronized. (b). CLKO1 will not be a 50% duty cycle. (c). CLKO2 output (if enabled) will be the frequency of PLL's output before division. MOTOROLA MC68360 USER’S MANUAL ERRATA For More Information On This Product, Go to: www.freescale.com...
- Page 28 QUICC to be the input clock of other QUICC(s) is not recommended. When using a crystal, the CLKO1 output does not meet the jitter requirements of the EXTAL input. MC68360 USER’S MANUAL ERRATA MOTOROLA For More Information On This Product,...