hit counter script
Siemens HUB-4 Installation Instructions Manual
  1. Manuals
  2. Brands
  3. Siemens Manuals
  4. Switch
  5. HUB-4
  6. Installation instructions manual
Siemens HUB-4 Installation Instructions Manual

Siemens HUB-4 Installation Instructions Manual

Communication card for ncc wan/pmi-2 concentrator
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual

Installation Instructions

Model HUB-4
Communication Card for NCC WAN/PMI-2 Concentrator
INTRODUCTION
Figure 1
HUB-4 Communication
Card
P/N 315-099458-9
The Model HUB-4 Communication Card from Siemens Industry, Inc., mounts in the
CC-5 Card Cage and provides up to four independent data channels, which can be
wired as either Style 4 or Style 7 for communication to the remote XLS, MXL, XL3 or
other UL864 listed local fire alarm panel providing dry relay contacts that can be used
for event monitoring.
The HUB-4 consists of a single Main-2 board on which two COM-2 boards are
installed. In turn, up to two modem or RS-485 Interface blocks can be installed on
each COM-2 board. Each modem block installed provides a single FSK data channel.
Each RS-485 Interface block installed provides a proprietary RS-485 interface channel.
Either a RS-485 Interface or a Modem Block module can be used, dependent on
application. Table 1 describes the connections that can be made.
H
U
B
4 -
A
N
D
F
R I
E
P
A
P
A
N
E
L
R
S
4 -
8
C
a l
s s
B
S (
y t
e l
) 4
X
L
3
N
A /
M
X
L
N
A /
F
S
- I
M
X
L
N
M I
1 -
W
F
I S
X -
L
S
H
U
B
R /
P
M
O
h t
r e
W
A
O I
s
1 (
1 -
) 6
Each of the four data channels is controlled by a separate micro-controller which
provides all background supervision of the data lines (to the remote panel) as well as
sending and receiving Fire Panel information to the primary micro-controller. The
information from these four channels is concentrated into a single data stream and
sent to the NCC WAN via the NIC-C or the PMI-2 Concentrator via HNET. On NCC
WAN, the HUB-4 communicates on each of four ports with either the MMX (XL3
Modem), the CMI-300 (MXL modem), NIM-1 FSI (MXL FSI modem), NIM-1W (MXL
RS-485), RPM (XLS RS-485), HUB-4 (XLS RS-485), HUB-4 (XLS modem) or up to 16
WAIO (Wide Area Input Output) boards. On the PMI-2 Concentrator, the HUB-4
communicates on each of the four ports with either the NIM-1W/NIM-1M (MXL
Modem), NIM-1W (MXL RS-485), RPM (XLS RS-485), HUB-4 (XLS RS-485), or HUB-4
(XLS modem).
Using the Modem Block module, communication distance is 8 miles (CMI-300/MMX-1)
or 10 miles (HUB-4 to HUB-4) over 18 gauge twisted pair lines depending on the quality
of the communication wires (attenuation cannot exceed -23 dBm [CMI-300/MMX-1] or
T
A
B
L
E
1
N
E
L
S
A
N
D
C
O
N
N
E
C
T
O I
N
T
Y
P
E
5
M
O
D
E
M
C
a l
s s
A
C
a l
s s
B
S (
y t
e l
) 7
S (
y t
e l
) 4
N
A /
M
M
X
N
A /
C
M
I
3 -
0
0
N
A /
N
M I
1 -
W
1 /
M
a
n
d
M
o
d
e
m
B
o l
k c
H
U
B
H
U
B
W
A
O I
s
N
A /
1 (
1 -
) 6
Building
Building
Building T T T T T ec
Building
Building
S
C
a l
s s
A
S (
y t
e l
) 7
M
M
X
N
C
C
W
A
N
o
n
y l
C
M
I
3 -
0
0
N
A /
N
C
C
W
A
N
r o
P
M
I
2 -
C
o
c n
e
n
r t
t a
r o
N
A /
N
A /
N
C
C
W
A
N
o
n
y l
Siemens
Siemens
Industry
Industry
Industry, , , , , Inc.
Siemens
Siemens Industry
Siemens
Industry
ec
ec
echnologies Di
ec
hnologies Di
hnologies Di
hnologies Division
hnologies Di
vision
vision
vision
vision
Inc.
Inc.
Inc.
Inc.

Advertisement

Table of Contents
loading

Related Manuals for Siemens HUB-4

Summary of Contents for Siemens HUB-4

  • Page 1: Installation Instructions

    (XLS modem). Using the Modem Block module, communication distance is 8 miles (CMI-300/MMX-1) or 10 miles (HUB-4 to HUB-4) over 18 gauge twisted pair lines depending on the quality of the communication wires (attenuation cannot exceed -23 dBm [CMI-300/MMX-1] or...

  • Page 2: Operation

    WAN head end system. In addition, the HUB-4 can support FSI protocol to communi- cate to an MXL using a NIM-1W or to an XLS using a HUB-4 slave so that an NCC or a Desigo CC via the PMI-2 Concentrator will act as the remote management system.

  • Page 3: Pre-Installation

    (Refer to Figure 1 for the location of the switches.) The address for the HUB-4 must be the same as the address selected for it in the NCC WAN/PMI-2 Concentrator. To set the address, turn the pointers on each of the three dials to the numbers for the selected address.
  • Page 4 HUB-4 Main -2. When assembling the HUB-4, note that P1, the 2 X 15 receptacle on the HUB-4, Main-2, connects to Port 1, P2 connects to Port 2, P3 connects to Port 3, and P4 connects to Port 4.
  • Page 5 Using the three nylon spacers provided with each HUB-4, COM-2, place the screw end of the spacers through the holes in the top of the HUB-4, Main-2 board. (Refer to Figure 4, page 5.) Secure the spacers in place on the underside of the HUB-4, Main-2 board with the nylon nuts provided.
  • Page 6 I t n I Figure 5 Connecting the HUB-4 Assembly Prior to installing the modem or RS-485 interface modules on the COM-2 card, configure them as indicated in Figures 6 and 7 . RS-485 INTERFACE MODULE JUMPER SETTINGS The RS-485 Interface module has two configuration jumpers: J2 and J3.

  • Page 7: Installation

    The HUB-4 assembly plugs perpendicularly into one slot in the CC-5 card-cage via two 96-pin DIN connectors and can occupy any slot in the card cage. (Refer to Figure 8.) Insert the HUB-4 card into the card guides rightside up (lettering on the front panel is legible) Slide the card in until the card edge connectors contact the receptacles on the motherboard.

  • Page 8: Post Installation

    Figure 8 Installing The HUB-4 WIRING All field wiring to the HUB-4 is connected to the terminal blocks of the CC-5 card cage slot in which it is installed. To Connect External Wiring Loosen the screw of the terminal by turning it counterclockwise.

  • Page 9: Electrical Ratings

    3. 14-18 AWG 8 miles max. 20 AWG 5 miles max. 22 AWG 3 miles max. 0.6 μF max line to line. Figure 9 Typical Class B (Style 4) HUB-4 Wiring Connection to CMI-300 on MXL Siemens Industry, Inc. P/N 315-099458-9 Building Technologies Division...
  • Page 10 3. 14-18 AWG 8 miles max. 20 AWG 5 miles max. 22 AWG 3 miles max. 0.6 μF max line to line. Figure 10 Typical Class A (Style 7) HUB-4 Wiring Connection to CMI-300 on MXL Siemens Industry, Inc. P/N 315-099458-9 Building Technologies Division...
  • Page 11 (24VDC @ 12A Max.) NOTES 1. The communication level from the MMX as measured from the HUB-4 terminals should not exceed -4dBm. 2. Positive or negative ground fault detected at <25K ohms on CC-5 pins 1-16. 3. 14-18 AWG 8 miles max.
  • Page 12 RS-485 INTERFACE 3 2. Positive or negative ground fault detected at <25K ohms on CC- ONE SLOT OF CC-2/5 5 pins 1-16. WITH HUB-4 INSTALLED 3. 200 ohms max per pair. 0.34 μF max line to line. Figure 12 TO PSC-12 TB4-...
  • Page 13 Installation Instructions, P/N 315-049930, and the Modem Block Installation Instructions, P/N 315-099356. Figure 14 Style 4 Wiring Between HUB-4’s (with RS-485 interface or Modem Block) 1. Mount LLM-1 in the XLS enclosure. Refer to LLM-1 120 OHM EOL installation instructions, P/N 315-093530, for further...
  • Page 14 -4 must be set to Style 4 Power limited to NFPA 72 per NEC 760 Figure 16 Style 4 Wiring Between HUB-4’s (with RS-485 interface) to RPM 1. 80 ohms max per pair (Does not include LLM-1) 2. 14 -18AWG Twisted pair or twisted shielded pair 3.
  • Page 15 MODEM OR MODEM OR OR RS-485 OR RS-485 INTERFACE INTERFACE Port #3 Port #4 ONE SLOT OF CC-5 #1 WITH HUB-4 INSTALLED NIM-1M Module Board Figure 18 Style 4 Wiring to NIM-1M (with Modem Block) Siemens Industry, Inc. P/N 315-099458-9...
  • Page 16 THIS PAGE HAS BEEN LEFT INTENTIONALLY BLANK Siemens Canada Limited Document ID A6V10233204 P/N 315-099458-9 Siemens Industry, Inc. Building Technologies Division Building Technologies Division 2 Kenview Boulevard Florham Park, NJ Brampton, Ontario L6T 5E4 Canada...

Table of Contents