Related Manuals for Fujitsu SK-96380-120PMT
Summary of Contents for Fujitsu SK-96380-120PMT
-
Page 1: Evaluation Board
Fujitsu Microelectronics Europe FMEMCU-UG-960001-15 User Guide MB96300 SERIES EVALUATION BOARD SK-96380-120PMT V1.0 USER GUIDE... -
Page 2: Revision History
2006-09-18 V1.1 PHu – misc. corrections 2006-10-19 V1.2 MWi – Jumper settings updated 2006-10-20 V1.3 MWi – External Bus Interface is not released for SK-96380-120PMT V1.0 2006-11-27 V1.4 CSc – Socket Note added 2007-03-02 V1.5 HWe/DGo - Recycling Note added This document contains 41 pages. -
Page 3: Warranty And Disclaimer
To the maximum extent permitted by applicable law, Fujitsu Microelectronics Europe GmbH restricts its warranties and its liability for the SK-96380-120PMT Board and all its deliverables (eg. software include or header files, application examples, target boards, evaluation boards, engineering samples of IC’s etc.), its performance and any consequential damages, on the use of the Product in... -
Page 4: Table Of Contents
Vcc 5 Volts (J4) ..................... 27 4.10 Vcc 3.3 Volts (J5) ....................27 4.11 Vcc 2.5 Volts (J9) ....................27 4.12 Vcc 1.8 Volts (J10) ....................27 4.13 LIN Bus Inhibit (J6)....................27 FMEMCU-UG-960001-15 - 4 - © Fujitsu Microelectronics Europe GmbH... - Page 5 7 PROGRAMMING THE INTERNAL FLASH MEMORY........... 34 Asynchronous Mode....................34 Synchronous Mode ....................36 8 APPENDIX ........................37 Related Products....................37 Information in the WWW..................38 Tables ........................39 Figures ........................40 Abbreviations ......................41 © Fujitsu Microelectronics Europe GmbH - 5 - FMEMCU-UG-960001-15...
-
Page 6: Overview
Chapter 1 Overview 1 Overview 1.1 Abstract The SK-96380-120PMT is a multifunctional evaluation board for the Fujitsu 16FX Flash microcontroller series MB96F38x. It can be used stand-alone for software development and testing or as a simple target board to work with the emulator system. -
Page 7: Features
SK-96380-120PMT User Guide Chapter 1 Overview 1.2 Features < Supports Fujitsu’s MB96387-LQFP(M21) MCU in 120-PMT package or the MB2198 Emulator System with the Probe Cable MB2198-16FX-120P-M21 < 9-15V unregulated external DC power supply < 5V, 3.3V, 2.5V and 1.8V onboard switching mode voltage regulators <... -
Page 8: General Description
SK-96380-120PMT User Guide Chapter 1 Overview 1.3 General Description The SK-96380-120PMT supports the 16-bit Flash microcontroller MB96F387-LQFP(M21) of the F MC-16FX Series. It can be used as a stand-alone evaluation board or as a target board for the emulator debugger. - Page 9 If the board is used as an emulator target board, the microcontroller must be removed from the socket and the corresponding probe cable has to be mounted: Series V-Chip Probe cable Socket MB2198-16FX-120P-M21 NQPack120SD MB96380 MB96V300 Table 1-1: Emulation System © Fujitsu Microelectronics Europe GmbH - 9 - FMEMCU-UG-960001-15...
-
Page 10: Installation
1. Power up the Emulator Main Unit (MB2198-01) 2. Power up the Adapter Board (MB2198-500), if needed 3. Power up the target Board (SK-96380-120PMT) To turn off the system, switch off the components in reverse order, beginning with the target Board. -
Page 11: Default Jumper Settings For Mb9638X
RS232 / LIN SOT2 UART2 Jumper 3 pin JP40 RS232 / LIN-Bus UART2 Jumper 3 pin JP41 DTR / DTRX selection Jumper 3 pin Open JP42 VBat LIN-Bus UART2 connector Jumper 2 pin Open © Fujitsu Microelectronics Europe GmbH - 11 - FMEMCU-UG-960001-15... - Page 12 Solder JP 2 pin Open JP60 ASX/ALE VG-48 connector* Solder JP 2 pin Open JP61 Ext. Vin VG-48 connector* Solder JP 2 pin Open Table 2-1: Jumper Settings * not supported on SK-96380-120PMT V1.0 FMEMCU-UG-960001-15 - 12 - © Fujitsu Microelectronics Europe GmbH...
-
Page 13: Jumper Location
SK-96380-120PMT User Guide Chapter 2 Installation 2.3 Jumper Location The following picture shows the silk plot of the starter-kit with marked default jumper settings. Figure 2-1: Default Jumper Settings © Fujitsu Microelectronics Europe GmbH - 13 - FMEMCU-UG-960001-15... -
Page 14: Software Installation
2.4 Software Installation 2.4.1 Installation of Softune Workbench With the “SK-36380-120PMT” Fujitsu supplies a full working development environment called Softune Workbench V30L33. To develop own software the Softune Workbench development environment must be installed first. Follow the instructions for successful installation of the Softune Workbench. -
Page 15: Jumpers And Switches
Table 3-1: MCU Operating Mode MD0 MD1 MD2 nc DIP-Switch S1 (default setting) Figure 3-1: MCU mode switch: Fixed Vector Mode MD0 MD1 MD2 nc DIP-Switch S1 Figure 3-2: MCU mode switch: Flash Programming Mode © Fujitsu Microelectronics Europe GmbH - 15 - FMEMCU-UG-960001-15... -
Page 16: Power Supply (S2, Jp:16, 17, 28, 22, 42)
No voltage supply to Vs of LIN JP22 Closed Board is always on (Mains) Open S2 switches the Board on and off Table 3-3: Power Supply Configuration By default, all Board supplies are set to 5V. FMEMCU-UG-960001-15 - 16 - © Fujitsu Microelectronics Europe GmbH... -
Page 17: Analog Power Supply Voltage (Jp: 11, 12, 13, 14)
If JP12 and JP13 are open, the resistors R16, R17, R20, and R21 define AVRH and AVRL. By default the resistor network (R16, R17, R20, and R21) is not mounted on the board. © Fujitsu Microelectronics Europe GmbH - 17 -... -
Page 18: Lin / Uart Connectors (X5 And X9)
LIN-UART0 is LIN Slave JP28 Closed Pin 1 (LIN Vs) of X5 is connected to Vin (LIN Vbat) Open Pin 1 (LIN Vs) of X5 is not connected to Vin Table 3-5: UART0 Settings FMEMCU-UG-960001-15 - 18 - © Fujitsu Microelectronics Europe GmbH... - Page 19 LIN-UART2 is LIN Slave JP42 Closed Pin 1 (LIN Vs) of X9 is connected to Vin (LIN Vbat) Open Pin 1 (LIN Vs) of X9 is not connected to Vin Table 3-6: UART2 Settings © Fujitsu Microelectronics Europe GmbH - 19 - FMEMCU-UG-960001-15...
-
Page 20: Can Interfaces (X6 And X8)
External reset generation is active JP48 (RST MCU) Open No external reset generation Table 3-8: Reset Connection By default, the external reset is enabled and set to immediate reset, the reset by UART is disabled. FMEMCU-UG-960001-15 - 20 - © Fujitsu Microelectronics Europe GmbH... - Page 21 If JP41 (DTR/DTRx) is set, the UART RESET jumper (JP33) and the according DTR/RTS (JP23 and JP38) jumper have to be set, too. If the reset LED is steadily on, check the power supply input voltage and the settings for the reset-generation by UART. © Fujitsu Microelectronics Europe GmbH - 21 - FMEMCU-UG-960001-15...
-
Page 22: User Buttons Sw1, Sw2, Sw3, Sw4, Sw5, Sw6 (Jp: 3, 4, 5, 6, And 7)
Pin 19 (IN1/TTG5/1) of the MCU is connected to “SW5” JP7 (SW5) Open No connection to the microcontroller Table 3-9: User Push Buttons Default: JP3, 4, 5, 6, 7 closed By default, all push-buttons are connected to the microcontroller. FMEMCU-UG-960001-15 - 22 - © Fujitsu Microelectronics Europe GmbH... -
Page 23: Connectors
Connected to DTR (pin 4) Can be connected with CTS by jumper Can be connected with RTS by jumper LGND Ground normally used for LIN connection Shield Ground Table 4-1: UART Connector Signals © Fujitsu Microelectronics Europe GmbH - 23 - FMEMCU-UG-960001-15... -
Page 24: Can Connector (X6, X8)
J1 are normally not mounted. If the used LC-Display has pins for LED backlight at this position, they can be connected here (Pin15: Vcc via 39U/0.5W, Pin16: GND). The following control signals are provided: FMEMCU-UG-960001-15 - 24 - © Fujitsu Microelectronics Europe GmbH... - Page 25 VCC GND LD8 LD7 LD6 LD5 LD4 LD3 LD2 LD1 Port 09_7 09_6 09_5 09_4 09_3 09_2 09_1 09_0 Table 4-3: User LEDs/LCD * Pin16: Vcc via 39U/0.5W for LCD Lightning © Fujitsu Microelectronics Europe GmbH - 25 - FMEMCU-UG-960001-15...
-
Page 26: In-Circuit-Programming Connector (X4)
Not used MCU mode-pin 0 Not used RSTX MCU reset signal SIN2 UART2 receive data SOT2 UART2 transmit data SCK2 UART2 clock Board supply voltage Ground Table 4-4: In-circuit programming connector FMEMCU-UG-960001-15 - 26 - © Fujitsu Microelectronics Europe GmbH... -
Page 27: Alarm Comparator Connector (J2)
To this connector the INH pin of the LIN1 transceiver is connected. 4.15 VCC Connector (J7) This connector holds the VCC supply. 4.16 GND Connector (J8) This connector holds the GND line. © Fujitsu Microelectronics Europe GmbH - 27 - FMEMCU-UG-960001-15... -
Page 28: Potentiometers
With the potentiometer RP2 the threshold voltage for the alarm comparator can be adjusted. Any voltage between VCC and GND can be set. It is connected to the comparator 0, thus to pin ALARM0. Additionally the adjusted voltage can be measured at connector J2. FMEMCU-UG-960001-15 - 28 - © Fujitsu Microelectronics Europe GmbH... -
Page 29: Getting Started
A double-click on one of the files will invoke the built-in editor, which supports syntax-highlighting, tags, and various other functions. Figure 6-1: Softune Workbench main window Note: You may customize the editor by a right-click on the editor window. © Fujitsu Microelectronics Europe GmbH - 29 - FMEMCU-UG-960001-15... - Page 30 F1. In many cases, you can get some useful hints how to solve the problem. Of course, you can also use the HELP-menu anytime during development or debugging. FMEMCU-UG-960001-15 - 30 - © Fujitsu Microelectronics Europe GmbH...
-
Page 31: Project Start-Up
Chapter 6 Getting Started 6.2 Project Start-up In order to allow a quick and smooth project start-up Fujitsu Microelectronics Europe supplies a template project as a reference. The easiest way to start a new project is to make a copy of the template project and use this copy as a start-up. The template includes the latest start.asm file, MCU header file, IRQ table, basic linker and C-Compiler settings. - Page 32 Chapter 6 Getting Started Rename into mb96380_template my_application Note that [DirInfo] entries are not needed to edit. 6. Start Softune Workbench and open your project Figure 6-2: Open Softune Workbench workspace (*.wsp) FMEMCU-UG-960001-15 - 32 - © Fujitsu Microelectronics Europe GmbH...
- Page 33 The starter-kit is delivered with the mode pin settings for the “Internal Vector Mode”. If the application should be programmed into the internal Flash memory, the mode pins have to be switched to the “Serial Programming Mode”. © Fujitsu Microelectronics Europe GmbH - 33 - FMEMCU-UG-960001-15...
-
Page 34: Programming The Internal Flash Memory
RS232 is selected (RS232/LIN) JP42 UART2 Open Vbat is not connected to Pin 1 of X9 (Vbat) JP38 UART2 Open DTR/RTS is not connected (DTR/RTS) Table 7-1: Jumper Settings for Programming FMEMCU-UG-960001-15 - 34 - © Fujitsu Microelectronics Europe GmbH... - Page 35 Then browse to the mhx-file you want to program to the embedded flash memory of the microcontroller. Press the button “Full Operation” to start programming. Note, that the COM port of the PC can be set in the Option ‘Set Environment’. © Fujitsu Microelectronics Europe GmbH - 35 - FMEMCU-UG-960001-15...
-
Page 36: Synchronous Mode
1 2 n/c MD0 3 4 MD2 RST 5 6 SIN2 X4: Flash programming socket SOT2 7 8 SCK2 VCC 9 10 GND Figure 7-2: Flash Programming Socket FMEMCU-UG-960001-15 - 36 - © Fujitsu Microelectronics Europe GmbH... -
Page 37: Appendix
Socket header for package LQFP-120 < (Tokyo Eletech Corp. www.tetc.co.jp/e_tet.htm) < MB2198-16FX-120P-M21 Emulator probe cable for MB96F38x MCU < MB96300 Series < MB96V300 MB96300 Series Evaluation chip < MB96F38x Flash MCU © Fujitsu Microelectronics Europe GmbH - 37 - FMEMCU-UG-960001-15... -
Page 38: Information In The Www
SK-96380-120PMT User Guide Chapter 8 Appendix 8.2 Information in the WWW Information about FUJITSU MICROELECTRONICS Products can be found on the following Internet pages: http://emea.fujitsu.com/microelectronics Microcontrollers (8-, 16- and 32bit), Graphics Controllers Datasheets and Hardware Manuals, Support Tools (Hard- and Software) http://www.fme.gsdc.de/gsdc.htm... -
Page 39: Tables
Table 4-2: CAN Connector Signals ..................24 Table 4-3: User LEDs/LCD....................25 Table 4-4: In-circuit programming connector ................ 26 Table 7-1: Jumper Settings for Programming............... 34 Table 7-2: Jumper Settings for reset signal ................35 © Fujitsu Microelectronics Europe GmbH - 39 - FMEMCU-UG-960001-15... -
Page 40: Figures
Figure 6-1: Softune Workbench main window ..............29 Figure 6-2: Open Softune Workbench workspace (*.wsp) ............ 32 Figure 7-1: Settings for Automatic Mode ................36 Figure 7-2: Flash Programming Socket................36 FMEMCU-UG-960001-15 - 40 - © Fujitsu Microelectronics Europe GmbH... -
Page 41: Abbreviations
Controller Area Network Chip Select Fujitsu Microelectronics Europe GmbH Local Interconnect Network Microcontroller Unit Printed Circuit Board SRAM Static Random Access Memory SDRAM Synchronous Dynamic Random Access Memory UART Universal Asynchronous Receiver Transmitter © Fujitsu Microelectronics Europe GmbH - 41 - FMEMCU-UG-960001-15... - Page 42 According to the European WEEE-Directive and its implementation into national laws we take this device back. For disposal please send the device to the following address: Fujitsu Microelectronics Europe GmbH Warehouse/Disposal Monzastraße 4a 63225 Langen FMEMCU-UG-960001-15 - 42 - © Fujitsu Microelectronics Europe GmbH...