Page 1
FORM NO. 3321-422 Rev A OPERATOR’S 08886 - 80001 MODEL NO. & OVER MANUAL ® ® SAND PRO 5020 To assure maximum safety, optimum performance, and to gain knowledge of the product, it is essential that you or any other operator of the machine read and understand the contents of this manual before the engine is ever started.
Distributor. In addition to genuine TORO replace- FOREWORD ment parts, the distributor also has optional equip- ment for the complete line of TORO turf care equip- The SAND PRO 5020 was developed to provide an ment. Keep your Toro all TORO. Buy genuine efficient, trouble free and economical method of TORO parts and accessories.
(After every two years, complete model and serial number to: The Toro replace the interlock switch in the safety system, Company, 8111 Lyndale Avenue South, whether it is working properly or not.)
Page 4
25. If major repairs are ever needed or assistance is enough to cause burns. required, contact an Authorized TORO Distributor. 17. If the machine ever vibrates abnormally, stop immediately, turn the engine off, wait for all 26.
Page 5
Safety instructions warranty of The Toro Company. Sound & Vibration Levels Sound Levels This unit has a continuous A-weighted sound pres- sure level of 82.5 dB(A), based on measurements of identical machines per Directive 91/386/EEC and amendments. This unit has a sound power level of 93 LWA, based...
Symbol Glossary SICHERHEITS- ALLGEMEINE UMKIPPGEFAHR ÜBERFAHRGEFAHR QUETSCHGEFAHR FÜR GESPEICHERTE HEISSE OBERFLÄCHE, ENERGIE, RÜCK VERBRENNUNGSGEFAHR ZEHEN ODER FUSS, VON WARNDREIECK SICHERHEITS- SCHLAG ODER FÜR FINGER ODER HÄNDE OBEN ANGESETZTE KRAFT WARNUNG AUFWÄRTSBEWEGUNG SICHERHEITSBLECHE NIE SICHEREN ABSTAND SICHEREN ABSTAND ZUR SICHEREN ABSTAND ZUR KINDER IN SICHEREM BEIZENDE FLÜSSIGKEITEN, CHEMISCHE...
Fuel tank capacity is approximately 20.8 l. Figure 1 1. Dipstick THE TORO COMPANY STRONGLY RECOM- MENDS THE USE OF FRESH, CLEAN, UNLEADED REGULAR GRADE GASOLINE IN TORO GASOLINE POWERED PRODUCTS. 5. Install the dipstick firmly in place.
Page 9
Before operating GASOLINE BURNS CLEANER, EXTENDS Group 1 Hydraulic Oil (Recommended ENGINE LIFE, AND PROMOTES GOOD START- for ambient temperatures consistently ING BY REDUCING THE BUILD-UP OF COM- below 38° C): BUSTION CHAMBER DEPOSITS. LEADED GASOLINE CAN BE USED IF UNLEADED IS Mobil Mobil Fluid 424 NOT AVAILABLE.
Page 10
Before Operating opening. Assure pour spout and funnel are clean. CHECK TIRE PRESSURE (Fig. 4) The tires are over-inflated at the factory for shipping purposes. Reduce the pressure to the proper levels before starting the machine. Correct air pressure in front and rear tires is 4–6 psi. Figure 4 1.
Page 11
Controls Traction and Stopping Pedal (Fig. 5–6)—The trac- tion pedal has three functions: one, to make the machine move forward, two, to move it backward and three, to stop the machine. Using the heel and toe of the right foot, depress the top of the pedal to move forward and bottom of the pedal to move back- ward or to assist in stopping when moving forward.
Page 12
Controls engine starts, regulate the choke to keep the engine Fuel Shut-Off Valve (Fig. 10)—Close the fuel shut- running smoothly. As soon as possible, open the off valve when storing the machine. choke by pulling upward to the “OPEN” position. A warm engine requires little or no choking.
Page 13
In case of emergency, the SAND PRO can be towed Also operate the lift lever to be sure of proper for a short distance. However, Toro does not recom- operation of all parts. Shut off the engine and mend this as a standard procedure.
Page 14
Operating OPERATING CHARACTERISTICS CAUTION Using the machine demands attention. To prevent tipping or loss of control, use care when entering and leaving sand traps. Use extreme caution around ditches, creeks or other hazards. Use cau- tion when operating the machine on a steep slope. Reduce speed when making sharp turns or when turning on hillsides.
Maintenance Minimum Recommended Maintenance Intervals Maintenance Procedure Maintenance Interval & Service Check battery fluid level Every 25 Every 100 Every Every Check battery cable connections hours hours 400 hours 800 hours Change engine oil Lube front wheel bearing Lube traction control linkage Replace the engine oil filter Inspect the remote air filter element Inspect the engine air filter element...
Page 17
Maintenance lightly with a DRY-TYPE LUBRICANT. CAUTION Before servicing or making adjustments to the machine, stop the engine,, pull wires off the spark plugs and remove the key from the switch. LUBRICATION The Sand Pro has (3) grease fittings that must be lubricated regularly with No.
Page 18
Maintenance CHANGING ENGINE OIL AND 1. Park the machine on a level surface and turn the engine off. FILTER 2. Pivot the seat upward. Change the oil initially after the first 8 hours of oper- ation; thereafter change the oil every 50 hours and 3.
Page 19
Maintenance 689 kPa psi to prevent damage to the ele- ment. B. Keep the air hose nozzle at least 5 cm from the filter and move the nozzle up and down while rotating the filter element. Inspect for holes and tears by looking through the filter toward a bright light.
Page 20
Normally, change the hydraulic oil and filter after every 500 operating hours. If the oil becomes conta- minated, contact your local TORO distributor because the system must be flushed. Contaminated oil looks milky or black when compared to clean oil.
Page 21
Maintenance hydraulic oil from running onto the machine components. 3. Remove the drain plug from reservoir and let hydraulic oil flow into the drain pan. Reinstall and tighten the plug when hydraulic oil stops draining. Figure 20 1. Hydraulic oil filter CHECKING HYDRAULIC LINES AND HOSES After every 100 operating hours, check hydraulic...
Page 22
Maintenance 3. Loosen the lock nut on the spring adjusting pin 7. Operate the traction pedal in forward and until the bearing moves freely from the cam on reverse directions. If the wheel rotates in the the lever, allowing pump shaft freedom to rotate correct direction, stop the engine and adjust the during start-up.
Page 23
Maintenance 4. Install the new filter with arrow on the filter body pointing away from the fuel tank (toward the carburetor). Figure 24 1. Traction adjustment cam WARNING Figure 23 The engine must be running so final adjust- 1. Fuel filter ment of the traction adjustment cam can be 2.
Maintenance may be needed. 1. Park the machine on a level surface, turn off the engine and block the wheels. 2. Loosen the jam nut on the adjustment rod clevis. Figure 25 1. Control rod ADJUSTING THE STEERING WHEEL TILT LEVER If the steering wheel tilt lever does not lock after adjusting the wheel position, an adjustment to the lever is required.
WARNING To order replacement parts from an authorized Connecting cables to the wrong post could TORO distributor, supply the following information: result in personal injury and/or damage to the electrical system Model and serial numbers Part number, description and quantity of parts 3.