19lh2/22lh2/26lh2/32lh2/37lh2/42lh2/32lf2/42lf2/32lh3/37lh3/42lh3/47lh3/19lu5/22lu5/26lu5/37lh5/42lh5/47lh5/55lh5/32lh6/42lh6/32lh7/37lh7/42lh7/47lh7/42lh9/47lh9/55lh9 series (126 pages)
LCD TV SERVICE MANUAL CHASSIS : LD75A MODEL : 42LF66 42LF66-ZE CAUTION BEFORE SERVICING THE CHASSIS, READ THE SAFETY PRECAUTIONS IN THIS MANUAL. Downloaded From TV-Manual.com Manuals...
SAFETY PRECAUTIONS IMPORTANT SAFETY NOTICE Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the Schematic Diagram and Replacement Parts List. It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent Shock, Fire, or other Hazards.
SERVICING PRECAUTIONS CAUTION: Before servicing receivers covered by this service unit under test. manual and its supplements and addenda, read and follow the 2. After removing an electrical assembly equipped with ES SAFETY PRECAUTIONS on page 3 of this publication. devices, place the assembly on a conductive surface such as aluminum foil, to prevent electrostatic charge buildup or NOTE: If unforeseen circumstances create conflict between the...
Page 5
IC Remove/Replacement Some chassis circuit boards have slotted holes (oblong) through Circuit Board Foil Repair which the IC leads are inserted and then bent flat against the Excessive heat applied to the copper foil of any printed circuit circuit foil. When holes are the slotted type, the following technique board will weaken the adhesive that bonds the foil to the circuit should be used to remove and replace the IC.
Page 7
5. Chroma & Brightness 5-1. FHD Module-47LF66 Item Unit Measurement Result Remark Viewing Angle Viewing <CR>10> Angle<CR>10> White average - 100IRE Full White Pattern(255gray) 47LF65 cd/m brightness - Picture : Dynamic (Cool) - 100IRE Full White Pattern(255gray) Brightness uniformity cd/m - Picture : Dynamic (Cool) Color White...
Page 8
5-2. FHD Module-42LF66 Item Unit Measurement Result Remark Viewing Angle Viewing Angle <CR>10> <CR>10> White average 42LF65 cd/m - 100IRE Full White Pattern (255gray) brightness - Picture : Dynamic (Cool) Brightness uniformity cd/m - 100IRE Full White Pattern (255gray) - Picture : Dynamic (Cool)
Page 9
5-3. FHD Module-37LF66 Item Unit Measurement Result Remark Viewing Angle Viewing Angle <CR>10> <CR>10> White average 37LF65 cd/m - 100IRE Full White Pattern (255gray) brightness - Picture : Dynamic (Cool) Brightness uniformity cd/m - 100IRE Full White Pattern (255gray) - Picture : Dynamic (Cool) Color White 0.261...
Page 10
6. Component Video Input (Y, P Resolution H-freq(kHz) V-freq.(kHz) Pixel clock(MHz) Proposed 720*480 15.73 59.94 13.500 SDTV, DVD 480I(525I) 720*480 15.75 60.00 13.514 SDTV, DVD 480I(525I) 720*576 15.625 50.00 13.500 SDTV, DVD 576I(625I) 720*480 31.47 59.94 27.000 SDTV 480P 720*480 31.50 60.00 27.027...
Page 12
Model Name : 47LF66 / Check Sum HDMI1 : D71D , HDMI2 : D70D Model Name : 42LF66 / Check Sum HDMI1 : DC1D , HDMI2 : DC0D Model Name : 37LF66 / Check Sum HDMI1 : D81D , HDMI2 : D80D - 12 - Downloaded From TV-Manual.com Manuals...
Page 13
Cell pitch 541.5um (H) x 541.5um (V) G cell Color arrangement RGB stripe arrangement Weight(net) Net 1EA 9-2. General specifications-42LF66: LC420WU2-SLB1 Item Unit Remark Display area 930.24 (H) * 523.26 (V) Outline dimension 983 (W) x 576 (H) x 51 (D)
Page 14
1144.5 825.6 With Stand After Packing 1230 Product Only SET 37.46 kg With Stand Weight With BOX 44.7 kg 10-2. 42LF66 Item Content Remark Product Width (W) Length (D) Height (H) Dimension Before Packing 1033.1 With Stand After Packing 1119...
This spec. sheet is applied to all of the LD75A chassis 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F manufactured at LG TV Plant all over the world. 00 00 FF FF FF FF FF FF 00 1E 6D Ex.) LD75A : 37/42/47LB5DF-ZC, 37/42/47LY3DF-ZA...
Page 16
5. Method of Tool Option setting 3) Press IN-START key on R/C for adjustment. 5.1. Press ADJ Key in the Adjust remocon. 5.2. Select "Tool Option1 and 2" by using (CH+/-) key, and Press Number Key. 5.3. Model Table. Model name Tool Option1 Tool Option2 37LF65...
3) Press the IN-START key on R/C for adjustment. PC (for communication through RS-232C) -> UART Baud rate : 115200 bps * Connecting picture of the measuring instrument (On Automatic control ) Inside PATTERN is used when W/B is controlled. Connect to auto controller or push control R/C IN-START ->...
Page 18
5) When the R/G/B GAIN is 80 on OSD, it is the FULL DYNAMIC Range of the Module. In order to control white balance without the saturation of FULL DYNAMIC Range and DATA, one of R Gain / G Gain / B Gain should be kept on 80, and other two is controlled lowering from 80.
TROUBLESHOOTING 1. No power (1) Symptom 1) Doesn't minute discharge at module. 2) Non does not come in into the front LED. (2) Check follow Is plug in power cord? Plug in power cord Is connect the Line Connect cable. Filter and Power Board Cable? Is normal the...
Page 20
2. Protect mode (1) Symptom 1) After once shining, it does not discharge minutely from module. 2) The relay falls.(The sound is audible “Click”.) 3) It is converted with the color where the front LED is red from green. (2) Check follow Is output the normality Low/High Is normal the Power Replace Power Board.
Page 21
3. No Raster (1) Symptom 1) No OSD and image occur at screen. 2) It maintains the condition where the front LED is green (2) Check follow Is output the normality Does minute Replace the Power Is the inverter on? Low/High voltage except discharge board.
Page 22
4. In case of occur strange screen into specific mode 1) In case of does't display the OSD (1) Symptom 1) LED is green. 2) The minute discharge continuously becomes accomplished from module (2) Check follow Is normal the LVDS Replace Power Board.
Page 23
2) In case of does't display the screen into specific mode (1) Symptom - The screen does not become the display from specific input mode (RF, AV, Component, RGB, DVI). (2) Check follow (1) Check the all input mode should become normality display. (1) Check the Video(Main)/Data(Sub), Video(Main)/Video(Sub) should become normality display from the PIP mode or DW mode.
Page 24
(4) In the case of becomes unusual display from side S-video/AV mode Is Video input of the Check the input source. AV Jack (P1400) normal? Is normal the Input voltage, Is normal the Replace IC IICCommunication and HV sync? CXA2069Q? Same as Block A (5) In the case of becomes unusual display from Component, RGB mode Is R,G,B input and...
Page 25
(7) In the case of becomes unusual display from SCART1 mode Is Video input Check the input source. of A/V jack normal? (J1200) Same as Block A (8) In the case of becomes unusual display from SCART2 mode Is Video input Check the input source.
Page 26
5. In case of no sound (1) Symptom 1) LED is green. 2) Screen display but sound is not output (2) Check follow Is the speaker Set on speaker in All input (mode) On it men? menu. is no sound? Is the speaker Check the Speaker Cable normal?
Page 48
[POWER BLOCK] TDFC-G106P TU600 C612 C616 0.1uF 47uF 5V_TU 5.0V For only C.I. 3.3 volt % MUST BE PLACED NEAR IC100 IC600 GND_TU Over current protection can be operated TPS2010ADR IC504 5V_ANN_MNT 5.0V R652 KIA78R33F OUT4 TPS2010 IC507 OUT3 KIA78R05F GND_TU OUT2 R653...