Makita BTW072 Instruction Manual page 5
Hide thumbs
Also See for BTW072:
- Instruction manual (72 pages) ,
- Technical information (10 pages) ,
- Instruction manual (12 pages)
Advertisement
Checking the remaining battery capacity (Fig. 2)
When charging
When the charging begins, the first (far left) indicator
lamp begins to flicker. Then, as charging proceeds, the
other lamps light, one after the other, to indicate the bat-
tery capacity.
When using
When the tool is switched on, the lamps will light to indi-
cate the remaining battery capacity. When the tool is
switched off, the light goes out automatically.
If the battery has not been used for a long time, or is
needed refresh charging, the orange lamp begins to
flicker.
Use Makita refreshing adapter to refresh the battery.
CAUTION:
A battery cartridge extracted from the charger that has
been unplugged with the battery cartridge inserted does
not work even if it is inserted in the tool. At this time,
recharge it for about five seconds before use.
Installing or removing socket (Fig. 3)
CAUTION:
Always be sure that the tool is switched off and the bat-
tery cartridge is removed before installing or removing
the socket.
To install the socket, push it onto the anvil of the tool until
it locks into place. To remove the socket, simply pull it off.
Switch action (Fig. 4)
CAUTION:
Before inserting the battery cartridge into the tool, always
check to see that the switch trigger actuates properly and
returns to the "OFF" position when released.
To start the tool, simply pull the trigger. Tool speed is
increased by increasing pressure on the trigger. Release
the trigger to stop.
Reversing switch action (Fig. 5)
CAUTION:
• Always check the direction of rotation before operation.
• Use the reversing switch only after the tool comes to a
complete stop. Changing the direction of rotation
before the tool stops may damage the tool.
• When not operating the tool, always set the reversing
switch lever to the neutral position.
This tool has a reversing switch to change the direction of
rotation. Depress the reversing switch lever from the A
side for clockwise rotation or from the B side for counter-
clockwise rotation. When the reversing switch lever is in
the neutral position, the switch trigger cannot be pulled.
Auto-stop mechanism (Fig. 6)
The tool stops automatically after the battery capacity
reaches under 20% to prevent the lack of fastening
torque. (Red color lamp lights on.) Charge the battery or
use a new fully charged one.
Auto-stop setting for number of impacts
This tool has a convenient auto-stop mechanism that
allows you to preset the desired number of impacts in
terms of the application. The tool then stops automati-
cally after reaching the preset number of impacts.
1.
Pulling the trigger, insert the battery cartridge. Keep
on pulling the trigger after inserting the battery car-
tridge. (The indicating lamp on the back of the tool
will flash about 10 times, then the lamp will keep
lighting up lit.) (Fig. 7)
2.
Hit the tool housing around the grip once with a
screwdriver etc. (The indicating lamp will go out.)
(Fig. 8)
3.
Release the trigger. (The indicating lamp will keep
lighting up lit for 0.5 seconds, then the lamp will go
out.) (Fig. 9)
4.
Hit the tool housing preset number of first digit
except 0. (The indicating lamp will light up in green
color. Then, the light goes out. )
Example: When the presetting number is 12, hit the
tool housing once.
5.
Pull the trigger, then release it.
6.
Hit the tool housing preset number of second digit
except 0. (The indicating lamp will light up in red
color. Then, the light goes out.)
Example: When the presetting number is 12, hit the
tool housing two times.
7.
Pull the trigger, then release the trigger. (The indicat-
ing lamp will light up.)
8.
Remove the battery cartridge. (Presetting has fin-
ished.) (The indicating lamp will go out.)
CAUTION:
When you change the presetting, do the same procedure
as above 1 – 8.
5
Advertisement
